Maximum psi of a Taskmaster Steel Modular Trailer Wheel

Question

Question:

What is the maximum psi rating of this rim? Item # 560550SM1 Will it accept the 80psi of my load range E tires? Thanks

asked by: Ronb N

0

Expert Reply:

A trailer wheel's maximum psi is determined by its valve stem. The Taskmaster Trailer Wheel # 560550SM1 includes a valve stem rated up to 80 psi so it'll work great with your tires.

expert reply by: Charles S

0

Answer 1

Yes, there is 15 teeth per each gear on the Replacement Gear Kit for etrailer and Ram Sidewind Jacks #TJA-2000S-GR. These gears have a thickness of 0.5", an OD of 1.36", and an ID of 0.5".

view full answer...

Answer 2

An ST205/75-15 trailer tire will fit on 15 x 5 to 15 x 6-1/2 inch wheels but will not fit a 15 x 7 inch wheel. Wheel width is not the overall width. It is the width where the tire sits, bead seat to bead seat. So if you are measuring the overall…

view full answer...

Answer 3

While we don't carry 225/75R15 tires with a 12 ply rating, I can say that they will work just fine on a wheel rated for 2,830 lbs like the Dexstar Steel Spoke Trailer Wheel #AM20532 so long as you don't exceed the weight capacity of the wheel…

view full answer...

Answer 4

The Taskmaster Wheel and Tire Combo 4.80-12 part #AM30660 that you referenced has a 90 psi max rating. You'd want to inflate them to 90 psi when cold and you'd be set. 100 psi would be too much.

view full answer...

Answer 5

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 6

Since Atwood was bought out their products' discontinued replacement parts are scarce. The remaining Atwood landing gear parts we have are shown on the linked page. We do have some bevel gear kits for other jacks, such as #LC146060, but these…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Maximum psi of a Taskmaster Steel Modular Trailer Wheel

Product Page this Question was Asked From

Continue Researching