Difference in Bearing Race # L68111 and Bearing Race # L68110

Question

Question:

I am having trouble finding kits with the l68110 race in it and the few things i have read say they are different races with different dimentions. are they interchangeable? thanks.

asked by: Ray D

0

Expert Reply:

Race # L68111 has an outer diameter of 2.361 inches.

Race # L68110 has an outer diameter of 2.327 inches.

Based on these measurements, the two races are not interchangeable. They are designed for different size hubs, but can use the same # L68149 bearing.

There may not be a pre-packaged kit with the L68110 race, but you can still get all the parts you need separately. I have included a link to our bearing and race main page for you to view.

expert reply by: Michael H

0

Kirk H.

6/5/2020

Need a bearing seal for L68110 race. 2.327" OD and a inner bearing L68149 with ID of 1.374" or so. Do you have these seals?

Reply

Chris R.

6/9/2020

The inner bearing # L68149 is typically used with a 10-19 grease seal, part # RG06-050. I would still try and verify that this is the correct replacement seal for your hub though. This seal has a 1.719" inner diameter and a 2.565" outer diameter.

Reply

Alan R.

5/22/2024

SKF - BR13 contains the LM68149 and LM68110 together SKF - BR17 contains the LM68149 and LM68111 together Both should be in stock or by quick acquisition at any auto parts store.

Reply

Miker

10/11/2025

Timken SET 13 vs SET 17, just figured it out myself, I'm not positive but I think Timken came up with all of these SET numbers, SET 12 is the outer bearing on my hub. Also easily found on rockauto. @AlanR

Reply

Josh

2/14/2025

Is the gasket the same in both sets?

Reply

Answer 1

Both races you mentioned are related to the same bearing, #L68149. The difference in the races is the outer diameter. The outer diameter is important for the hub that the race fits so because the hub bore in the rotors is different than the hubs you…

view full answer...

Answer 2

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 3

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 4

Trailer or automotive wheels can have a positive or negative offset. The offset refers to the distance between the mounting surface of the wheel that touches the hub and the center line of the wheel, as shown in the diagram I have edited for you. A…

view full answer...

Answer 5

You mentioned you have a manual pull down awning on your RV, and you can convert it, but you would not be able to use the conversion kit with arms, as they are not compatible with pull down styles, and the dryer vent would also interfere. What you…

view full answer...

Answer 6

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 7

In order to determine if there is space for both a slide topper and standard awning on your 2020 Grand Design Reflection 303RLS you will need to have at least 3" from the inside of the flange on the side of the slide to the outside of the…

view full answer...

Answer 8

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 9

The first thing you will need to get a 7-way connector on the rear of your 2012 Toyota FJ Cruiser, is part #ETBC7. This will attach to the 4-way connector you currently have and with additional wiring, give you a 7-way connector at the rear of your…

view full answer...

Answer 10

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 11

There are 2 ways to figure out exactly what you need Chris as I cannot look up parts for your 2004 EZ Loader boat trailer based on just a model. If you have the VIN you or I can contact EZ Loader to verify the correct bearings and seals used on your…

view full answer...

Answer 12

In order to find the correct replacement hubs for your Shoreland'r boat trailer, you need to first know what bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the…

view full answer...

Difference in Bearing Race # L68111 and Bearing Race # L68110

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching