Could etrailer Caster Wheel # JWK-6P Fit Fulton Jack

Question

Question:

Can the etrailer Poly Castor wheel replace my 6inch X 2inch Fulton trailer jack wheel? It looks the same in the photos and videos.

asked by: Paul

1

Helpful Expert Reply:

If the dimensions match technically it would fit but normally we don't recommend mixing brands.

I attached a picture that shows the dimensions of the sleeve and bolt that comes with the part # JWK-6P.

Basically if the 1/2 inch bolt is the same as what you have on your Fulton then it should work fine.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Kelly, the etrailer Boat Trailer Jack #MJ-1200B you're referring to has an outer tube diameter of 2" and an inner tube diameter of 1 3/4". The wheel that comes with this jack is a JWK-6P #JWK-6P, and the bolt measures 3", has a…

view full answer...

Answer 2

I went out into our warehouse and measured one for you. The overall width of this Dutton-Lainson Replacement 6 inch Poly Wheel #DL22440 is 2 inches. If you can email me back with the brand and model number (if you can find it), for you jack I can see…

view full answer...

Answer 3

I went out into our warehouse and measured one for you. The overall width of this Dutton-Lainson Replacement 6 inch Poly Wheel #DL22440 is 2 inches.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Could etrailer Caster Wheel # JWK-6P Fit Fulton Jack

Product Page this Question was Asked From

Continue Researching