Jack Recommendation for a Triton Boat Trailer

Question

Question:

do you know if this is jack used by triton boats.I cant find a number.but it is welded and is held on by a c ring.

asked by: Todd W

0

Expert Reply:

From the research that I did I found that Triton used Fulton jacks on a lot of their boat trailers.

While this Fulton Round, Snap-Ring Swivel Marine Jack, part # FTJ120W0301, may not necessarily be the exact same one that is on your boat trailer it should install onto your trailer.

The first thing I would consider when replacing a trailer jack is the capacity needed. The # FTJ120W0301 has a capacity of 1,200 lbs. If that would be adequate for your application. We carry similar jacks with capacities that range from 800 lbs to 1,600 lbs.

expert reply by: Jameson C

0

Answer 1

Hi Jared, You can upgrade from the Fulton #FTJ120W0301, and while you mentioned options for an upgrade, there really is just one that is going to work with your bracket, which is the jack you mentioned, the Fulton XLT Boat Trailer Jack #F141132. This…

view full answer...

Answer 2

The standard outer tube for a trailer jack has 2-1/4" diameter , which is very close to the 2-3/8" you mentioned. You may want to measure the diameter of your outer tube using a caliper like #PTW80157 to make sure you get an accurate…

view full answer...

Answer 3

The Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 provides similar capacity and does have a Snap ring pilot hole diameter of 2-1/2"that lines up with your Bulldog Jack.

view full answer...

Answer 4

Based on my research, the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will be a perfect replacement for your Shelby 5756A trailer jack. This jack will allow you to use the existing snap ring jack mount on your trailer for installation.…

view full answer...

Answer 5

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Answer 6

Hi Kenneth, The Fulton Boat Trailer Jack w/ Wheel #FTJ120W0301 is a great cost effective option for your trailer. It's going to come with a weld-on mounting plate and snap ring to attach the jack. It has a 1,200lb capacity, comes with a wheel…

view full answer...

Answer 7

Hello Jim, The Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K #FTJ120W0301 is rated for 1,200 pounds. Keep in mind that this rating applies to the tongue weight of the trailer, not the overall trailer weight. For…

view full answer...

Answer 8

The correct replacement for the Fulton Magnum Series Trailer Jack on your trailer is the Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 if you have a bolt-thru mounting bracket or part #FTJ120W0301 if you have a snap-ring mounting bracket. I…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Jack Recommendation for a Triton Boat Trailer

Product Page this Question was Asked From

Continue Researching