Replacement Pads For 4 Inch Wide Nerf Bars With 24 Inch Step Pad

Question

Question:

I have a 5 pin 4 inch wide 24 inch longoriginal equip nerf barb step pad thats broken do you have a replacement.

asked by: Anthony C

0

Expert Reply:

It sounds like you need the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 # 21-0001. You can see the measurements in the photo and that there are 6 pegs, but only 5 of them use the clips to hold the pads in place. You will also need 5 barrel clips, # 23-0002. The clips are sold as singles so you will need to change the quantity to 5.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hello John. We do offer replacement step pads for the Aries 4" oval nerf bars. There are two different options available though, so you will need to take a closer look at one of your pads in order to determine the correct replacement. Look at…

view full answer...

Answer 2

Thank you for those dimensions, and I think we may have what you need for your Tacoma with the following part: - Replacement Step Pad for Westin Platinum Series Oval Nerf Bars #21-0001 I have added a photo with the measurements of this replacement…

view full answer...

Answer 3

With 5 holes, you most likely have Westin nerf bars. I recommend the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 #21-0001 which are 24 inches by 4 inches.

view full answer...

Answer 4

The closest thing we have is the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 #21-0001. This pad has the 6 pins instead of the 4 pins you stated, but may fit based on the location of your 4 pins.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Replacement Pads For 4 Inch Wide Nerf Bars With 24 Inch Step Pad

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching