Locating Blue Brake Wire On 2014 Ford F-150

Question

Question:

where do i find the blue wire at the rear?

asked by: Henry

0

Expert Reply:

There are some wires that run along the frame rail on your 2014 F-150.

I have attached a photo that shows where you can find the wires. They will be on the driver side. I have attached a link to a helpful article on installing a brake controller on a Ford truck you can check out.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Hey Cecil, thanks for the information, I sure can. Since your F-150 doesn't have the towing package you'll need the Universal Installation Kit item #ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the…

view full answer...

Answer 2

There are two potential locations the port may be in your 2014 Ford F-150 to install the Plug-In Wiring Adapter for Electric Brake Controllers #22292. One is below your steering wheel column, above the pedals and the other is behind the panel that is…

view full answer...

Answer 3

Brake controller wiring harness #22292 plugs into the built-in connector beneath your vehicle's dashboard. To access this connector, first locate the instrument cluster finish panel in the center of you dash, near the driver's side. Carefully…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Locating Blue Brake Wire On 2014 Ford F-150

Featured Help Information

Miscellaneous Media

Continue Researching