How To Install A 4-Flat To 7-Way Wiring Harness Adapter On Your Vehicle
Updated 06/06/2017 | Published 06/05/2017
Question:
Looking for a trailer harness 7way plug for a 2011 Nissan Pathfinder. Would prefer one that has both 4 and 7 way connectors like the Hopkins connectors. Thanks
asked by: Tony C
Expert Reply:
In order to install a 4-flat and 7-way wiring harness on your 2011 Nissan Pathfinder, you will want an adapter if you already have a factory 4-way trailer connector or a complete wiring harness if you do not have a trailer wiring harness at all.
If you currently have a 4-way harness installed on the vehicle, I recommend the Adapter 4-Pole to 7-Pole and 4-Pole part # 37185. The new adapter will plug into your existing 4-way and will require you to run an additional 4 wires. The first wire you will need to run is the ground (white wire). The next wire you will have to install is the brake controller (blue wire) which is located on a black pigtail mounted to the frame near the factory 4-way connector. You will also need to run the power (black wire) to a 12 volt source which is also located on the black pigtail attached to the frame. The auxiliary (purple wire) will only need to be ran if applicable.
If you do not have a factory 4-way harness installed on your vehicle, you will need a wiring harness such as the T-One Vehicle Wiring Harness part # 118266. You will also have to replace the 7 way connector in this kit with the Hopkins Endurance Connector part # HM40950 to retain both 4-flat and 7-way connections.
I have attached a few review/installation videos in addition to our 7-way wiring diagram for your viewing.
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: Installing the Curt Powered Tail Light Converter on a 2025 Kia Carnival
- Shop: Trailer Wiring
- Q&A: 7-Way/4-Way Combo for Ford F-150 Where Both Can be Accessed at Same Time
- Q&A: Changing to 4-Way and 7-Way Connector on a 2017 Honda Ridgeline
- Q&A: Comparing the Hopkins 7-way part # HM40950 and Pollak Replacement 7-Pole # PK11893
- Shop: Mounting Bracket and Installation Hardware - Pollak 7-Pole, RV-Style Trailer Connector - Vehicle End
- Q&A: Recommended 7-Way Trailer Connector on a 2002 Ford Excursion to Replace Factory Connector
- Q&A: Is it Better to Switch to a 7-Way Blade Style Trailer Connector Over a 7-Way Round Pin
- Q&A: How Much Clearance is Needed Behind 7-Way Trailer Connectors # PK11898 and # HM48470
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ No Drop - 4 Bolt - 2K
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: hitch cargo carrier
on Custom Fit Vehicle Wiring
