Hand Winch Replacement Recommendation for Shelby 5466

Question

Question:

Do you have a winch replacement handle for Shelby 5466?

asked by: Hunter

0

Expert Reply:

We have some very similar winches to the Shelby 5466 that you have but we do not carry Shelby winches any longer. The Shelby is a 2 speed winch with a 2,300 lb capacity so for a very similar winch we have the Dutton Lainson 2 speed winch part # DL15440 which would work great. It has a bit more capacity at 3,200 lbs but that just means it'll crank in your boat even easier. Aside from that the winches are very similar.

I attached a link to a review video for this for you to check out as well.

expert reply by: Jameson C

0

Eduardo V.

7/26/2020

Hand Winch replacement for Shelby 5467?

Chris R.

8/1/2020

Unfortunately I wasn't able to find any information on that model Shelby winch. Do you know what it was rated for?

Eduardo V.

8/1/2020

@ChrisR I have a 27 ft boat I think it’s for 2800 lbs. it came with the trailer

Chris R.

8/11/2020

@EduardoV Thanks for the info! I think the Fulton # F142421 will work really nicely as a replacement. It offers a bit more capacity with a 3,200 pound limit and features a zinc, corrosion-resistant finish that makes it perfect for boat trailers.

Answer 1

The difference between the 9-1/2" Long Winch Offset Replacement Handle by Dutton-Lainson #DL70327 and 9-1/2" Long Winch Quick Attach Replacement Handle by Dutton-Lainson #DL70328 are the winches that they fit. The #DL70327 fits winch models…

view full answer...

Answer 2

Shelby is no longer in business and would not be the same as Fulton; there are no ratchet repair kits available for Shelby so you'll need to replace your winch. Keeping in mind that a boat trailer winch has a boat-size-to-winch capacity that is…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Hand Winch Replacement Recommendation for Shelby 5466

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching