What is the Diameter of the Clevis Pin Hole on the Clevis Adapter for B&W Tow & Stow BWTS35200B

Question

Question:

What is the diameter of the hole in this drew bar?

asked by: Kim B

0

Expert Reply:

The diameter of the clevis pin hole on the Clevis Adapter for B&W Tow & Stow 2-1/2" Ball Mounts, part # BWTS35200B, is about 1-1/8 of an inch.

expert reply by: Jon G

0

Answer 1

We have 3 different adapters for a B&W Tow & Stow and it all just depends on the size of your hitch receiver: 2" - #BWTS35100B 2-1/2" - #BWTS35200B 3" - #BWTS35300B These have 1-1/8" diameter holes for the clevis pin and…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 10

Hey Lucas! I measured the Buyers Products Weld-On Receiver Tube #337RT25824B in our warehouse using my digital caliper, and it has an exact outer diameter of 2.54", so I don't believe it will work with your truck's 2-1/2" receiver.…

view full answer...

Answer 11

Hey Tom! the gauge on the Big Truck Big RV Tongue Weight Scale for Trailers #BTBRV49FR has a +/- 5% full scale accuracy and displays weight in 50-lb increments up to 2,000 lbs. We also have it available with a SnapPad #BTBRV76FR for added stability.…

view full answer...

Answer 12

Hey Don, thanks for reaching out! The correct fit for your 2024 Ford F-250 with the Tremor package is the Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR. I confirmed with my contact at Hellwig that this will fit specifically with your Tremor…

view full answer...

What is the Diameter of the Clevis Pin Hole on the Clevis Adapter for B&W Tow & Stow BWTS35200B

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching