Ball Mount for 2-1/2 inch Hitch that Has 4 inches of Drop

Question

Question:

I AM LOOKING FOR A 2 1/2inch SQUARE, 4inch DROP HITCH. i HAVE THE BALL ALREADY DO YOU HAVE SUCH A PRODUCT SPEC, WITHOUT ADJUSTABLE BALL HITCHES? I AM NOT IN FAVOR OF THE MULTI DROP HITCH. THANKS

asked by: Jeff

0

Expert Reply:

We do have the Curt fixed ball mount part # C45458 which fits a 2-1/2 inch hitch and has a 4 inch drop like you said you needed.

I attached a review video for this ball mount for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I went out to the warehouse and found that the nut that comes with the B&W 2-5/16" Hitch Ball #BWHB94009 is 1-3/4" tall as you can see in the attached picture. The 2" diameter shanks that we have are all 3-1/2" long so there…

view full answer...

Answer 2

Here are the parts I recommend to help get you setup for towing with the B&W Heavy-Duty Ball Mount #BWBMHD30212: - 2-5/16" Hitch Ball #BWHB94050 - etrailer Hitch Receiver Lock #e98881 - Roadmaster Quiet Hitch #RM-062 The hitch ball has a…

view full answer...

Answer 3

The nut on a hitch ball with a 1-1/4" diameter shank, like the B&W #BWHB94002, takes an 1-7/8" socket, like #ALL643216 (for use with a 3/4" drive socket wrench) for example. Hitch balls with an 1-1/4" shank require 450 ft/lbs…

view full answer...

Answer 4

Hey Fred, yes you could remove the ball of the Curt ball mount part #C43JR, flip the ball mount over, and then reinstall the ball to use it as a rise ball mount instead. For basically the exact same thing but for a 2 inch hitch you would want the…

view full answer...

Answer 5

The Curt #C45458 ball mount uses a 5/8" hitch pin with clip or locking mechanism. For a simple pin and clip, you can use the Draw-Tite #PC3, or if you prefer a locking hitch pin I recommend the Fastway #FA86-00-3050 Receiver Lock. I have…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Ball Mount for 2-1/2 inch Hitch that Has 4 inches of Drop

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching