Recommend 10K lb, 2 Speed Crank, Weld-Mount Bulldog Jack For Gooseneck Trailer

Question

Question:

We have a warehouse gooseneck, with a single landing gear. I want to install tandem landing gear. I was given a number, 183902-2. is this a bulldog number?. I want atleast #10,000, spring loaded s. two speed crank. welded to trailer. is this the right number. it doesnot look like it.

asked by: Pete G

0

Expert Reply:

I contacted our representative at Bulldog, the item you selected, Bulldog Trailer Jack, part # BD183902, would be the correct jack you are looking for. The Bulldog Jack # BD183902 is a 10,000 lb capacity, spring loaded, 2 speed jack that is welded to the trailer.

In addition to part # BD183902, you will need the Bulldog Sidewind Jack Crank Assembly, part # BD015181.

I would recommend having a qualified welder install the Bulldog Trailer Jack # BD183902 on your gooseneck trailer.

expert reply by: Reno H

0

Christo S.

5/4/2020

I would like to know what Bulldog jack I would use in tandem with the BD183902 Bulldog 2-Speed Jack - Leg w/ Spring Return - Traditional - 26 Lift - 10,000 lbs?Thank you in advance for your reply

Chris R.

5/7/2020

For tandem operation the Bulldog Square Jack # BD182805 will work perfectly.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Recommend 10K lb, 2 Speed Crank, Weld-Mount Bulldog Jack For Gooseneck Trailer

Continue Researching