What Is Offset For Aluminum HWT Series S5 Trailer Wheel

Question

Question:

Interested in HWT Series S trailer wheel in 13 x 5, 4 x 4 bolt. What is the offset of the wheel and what lug flange angle is required. Using on trailer with wheel bolt and non studs.

asked by: John M

1

Helpful Expert Reply:

The HWT Aluminum Series S5 Wheel, part # AM22322HWTB has a zero offset. I called my contact at HWT and they told me the angle on the bolt holes are cut at a 45-degree angle.

expert reply by: Jeffrey L

1

Answer 1

Hey Tony, for a nicer looking 13 inch trailer wheel with a 4 lug bolt pattern we have a few options like the part #AM22322HWT, #AM22322HWTB, and #AM20270. We don't have the Valhalla style wheel with a 4 lug though.

view full answer...

Answer 2

Hey Kenny, for a black wheel that matches the specs you are looking for we have the #AM20242 which is 13 inch in diameter and has a 4 on 4 inch bolt pattern. Do you have a tire already?

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

What Is Offset For Aluminum HWT Series S5 Trailer Wheel

Continue Researching