Baking Plates for Electric Trailer Brakes

Question

Question:

I need a set of electric brake backing plates. size is 12 x 2 and has 4 hole mounting I am told there is a universal backing plate that will work. Can you help me?

asked by: Jerry

0

Expert Reply:

The 4-bolt backing plate we carry for electric trailer brakes is # D036-115-20. If this isn't the correct one for your brakes I've linked the rest of our selection for you.

expert reply by: Charles S

0

Answer 1

The dust shield cover for the Dexter Electric Trailer Brake Kit #23-434-435 is part #D036-115-20.

view full answer...

Answer 2

Hello Brandon, thanks for reaching out. The Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV is intended to be used with the #e43VV power unit and #e73VV. The legs are designed to be used in tandem, but they can be used for…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Baking Plates for Electric Trailer Brakes

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching