Do Baby Moon Wheel Covers # AM90086 Fit Dexstar Conventional Steel Wheel

Question

Question:

I need to know if the Americana Baby Moon Trailer Wheel Center Cap will fit the Dexstar Conventional Steel Wheel - 15inch x 6inch Rim - 6 on 5-1/2 - Black Powder Coat? Thanks!

asked by: Dusty P

0

Expert Reply:

Yes, the Baby Moon Covers # AM981306 that you referenced are a fit for the Dexstar Conventional Steel Wheel # AM20514.

expert reply by: Jameson C

0

Answer 1

I received your pictures but cant make out the exact measurements. Here are some different options with the different inner diameters. 10-1/4" #AM981306 10-1/2" #PX1307SS 11-11/16" #PX1309SS

view full answer...

Answer 2

You can determine whether either of our baby moon hubcaps, part #AM90086 or part #AM981306, will fit a wheel by measuring the outer diameter of the inner ring and then the outer diameter of the inner ring with one of the tabs (see attached photo).…

view full answer...

Answer 3

The Dexstar Conventional Steel Wheel #AM20514 you found is designed to use a Baby Moon Hubcap #PX1307SS. This style wheel does not accept a traditional Wheel Center Cap #LHCS108-SI60C. To use this style cap I recommend the Vesper Steel Modular…

view full answer...

Answer 4

If you are purchasing the Americana Pointed Top Baby Moon Trailer Wheel Center Cap #AM981306 then you will want a 15" wheel with a 6-lug pattern. For that I recommend the Dexstar Conventional Steel Wheel #AM20514, which has a 6 on 5-1/2"…

view full answer...

Answer 5

there isn't a guide to tell us the size of the hubcaps needed for your 2021 Gulf Stream Vintage Cruiser 19ERD travel trailer, but I do have a few options to choose from below once you've measured your wheel diameter and lug-nut bolt pattern:…

view full answer...

Answer 6

The style of the baby moon hub caps has not changed much at all so fit should be fairly universal so long as you get the right size as there are a few different options. The Phoenix USA Baby Moon Hubcap part #PX1307SS is designed for 13",…

view full answer...

Answer 7

Hey Lee, yes the Dexstar Conventional Steel Wheel #AM20514 you referenced is designed to use a Baby Moon Hubcap #PX1307SS. We have confirmed this as a fit so I apologize for any fit size info discrepancies.

view full answer...

Answer 8

The Phoenix USA #PX1307SS baby moon hub caps will only fit a conventional steel wheel like part #AM20514 with a 6 on 5-1/2 inch bolt pattern, because the raised lip around the lug holes is compatible with the inside dimension of the hubcap. Assuming…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Do Baby Moon Wheel Covers # AM90086 Fit Dexstar Conventional Steel Wheel

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching