What Is The Thread Pitch On The Replacement Trailer Hub Wheel Stud, Drive-In # RG03-020
Updated 01/06/2011 | Published 01/05/2011
Products Featured in This Question
Question:
what is the thread pitch ? also what drill hole dia. is used to on these ?
asked by: Ray
0
Expert Reply:
The hole size that the Replacement Trailer Hub Wheel Stud, Drive-In, part # RG03-020, will use is a 1/2 inch hole. The spline diameter on the wheel stud is 0.62 inches which is a little larger and that allows the wheel stud to have a press fit when driven into a 1/2 inch hole.
The thread pitch on the wheel stud is 1/2 x 20. It will accept the Chrome Trailer Wheel Lug Nut - 1/2 Inch, part # 12CLN, and the Trailer Wheel Lug Nut - 1/2 Inch, part # CE11051.
expert reply by:
Jeff D
0
Product Page this Question was Asked From
Replacement Trailer Hub Wheel Stud, Drive-In, 1/2" x 1-1/2" (Qty 4)
- Accessories and Parts
- Boat Trailer Wheels
- Trailer Hubs and Drums
- Trailer Tires and Wheels
- Wheel Studs
- 1/2 Inch Diameter
- Drive-In Stud
- 1-1/2 Inch Long
- Redline
more information >
Continue Researching
- Search Results: caliper
- Search Results: trailer axles accessories and parts
- Search Results: trailer axles
- Q&A: Replacement 3,500 lb Disc Brake Kit for a 2004 Ranger Boat Trailer
- Search Results: kodiak trailer brakes
- Search Results: kodiak 225 brake caliper
- Search Results: trailer springs
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Kodiak Disc Brake Caliper Review
- Shop: Kodiak Disc Brake Caliper - Dacromet - 2,000 lbs to 3,500 lbs - Driver Side
- Shop: Kodiak Disc Brakes - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs - E-Z Lube
- Shop: Dexter Boat Trailer Axle - 89" Long - Galvanized
- Q&A: Can I Use A Wheel Center Cap When Bearing Buddy Is Installed?
- Shop: Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs
- Shop: DeeMaxx Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Maxx Coating - 3,500 lbs
- Shop: Complete Bearing Kit with L44649 Inner/Outer Bearings and 10-9 Grease Seal Fits 1.063" Spindles
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: Can Hub and Brake Drum Be Replaced with Idler Hub on Tandem Axle Trailer
- Search Results: trailer hubs and drums
- Q&A: Are All 1/2 Inch Lug Studs Fine Thread 20 Threads Per Inch
- Q&A: How to Remove Trailer Wheel that Doesn't have Lug Nuts or Bolts
- Q&A: When Do Brakes Need to be Added to Both Axles of Tandem Axle Trailer
- Q&A: Do You Have the Instructions and User Manual for the Advent Air Low Profile RV Air Conditioner?
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)