Replacement Boat Trailer Jack for 1995 4 Winns Trailer with Welded Bracket

Question

Question:

Hi, Wondering if you would be able to offer a replacement jack that would fit the factory mounting bracket of my 1995 4Winns trailer. The hole pattern is 4 holes-4inch wide and 2.75inch high. I tried to add a picture but not sure it made it. Thanks for any help

asked by: Shane

1

Helpful Expert Reply:

I do have options for you but we do not offer any jacks that will fit the existing bracket you have on your trailer frame. Therefore, I recommend just using the Fulton Bolt-Thru Swivel Marine Jack part # FXP15L as it is a bolt-on fit that won't even require you to remove your existing bracket.

I am not sure which type of bracket you have now but most most of the time you end up just replacing the bracket and jack together as it is very difficult to try and find compatible parts, especially when the brand/model is not know. I do however know that most of these trailers used Shelby Jacks and if that is the case I can confirm there are no replacements that will work with this mount so a bolt-on option like the above is your only hope.

expert reply by: Conner L

1

click to enlarge

Answer 1

The Electric Trailer Brake Kit part #AKEBRK-35-SA is likely what you need for your Four Winns Boat Trailer. The 3,700 lb trailer axles usually use the same spindles as 3,500 lb trailer axles so as long as you have 10" assemblies (roughly) and…

view full answer...

Answer 2

Hello Johnny, thanks for reaching out. Sadly, no we are not able to look up trailer parts using a VIN. There just isn't a universal VIN database for trailers like there is for motor vehicles. Typically only the manufacturer of the trailer would…

view full answer...

Answer 3

Without knowing the part number and manufacturer of your current trailer jack, I couldn't speak to the compatibility of the mounting plate for your current jack with the mount that the Fulton #F141132 XLT uses. The #P9012-00 weld-on mount for the…

view full answer...

Answer 4

Thank you for the photo of your Fulton jack. Your jack is a bolt-thru type pull-pin swivel jack. The 1500-lb-rated Fulton jack you can use in place of your existing one is part #FXP15L.

view full answer...

Answer 5

I do have an option for you but Shelby boat trailer jacks are discontinued and we don't offer any direct bolt-on replacements for them. That said, you can easily remove the old flange by cutting or simply place the new jack beside it and leave…

view full answer...

Answer 6

We don't have any exact matches for what you have on your boat trailer so best option would be a new one that is similar like the #MJ-1206B which is a similar bolt on swivel jack with a sidewind handle.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Boat Trailer Jack for 1995 4 Winns Trailer with Welded Bracket

Continue Researching