Replacement Parts Needed for Brakemaster 9000 Where Air Leaks Out of 90 Degree Diaphragm

Question

Question:

Replacement diaphragm on supply line blown. Air leaks out end of 90° fitting. Cost of part/parts needed?

asked by: George D

0

Expert Reply:

I spoke with my contact at Roadmaster and sent him the picture you submitted and he said you would need the part # RM-450601-50 and the part # RM-450045

expert reply by: Jameson C

0

click to enlarge

Answer 1

I spoke with my contact at Roadmaster about helping you get the part #RM-450601-50 installed properly. Here was their response: Simply orient the Quick Exhaust Valve just like in the pictures, with the acorn top as the inlet and the bottom side port…

view full answer...

Answer 2

The replacement valve that you will need is #RM-450601-50. This is the replacement exhaust valve for the Roadmaster BrakeMaster system. The valve is a complete replacement. There is no rebuild kit or separate parts available for the unit.

view full answer...

Answer 3

I sent this to my tech contact at Roadmaster and they responded with the following: Without any other information, it sounds to me like the quick-exhaust valve (QEV) has failed. This is located near the base (but on the side) of the air cylinder that…

view full answer...

Answer 4

It sounds to me like you might have an issue with the connection of the ICX transmitter and the brake signal from the towed vehicle. You're getting the power to the ICX transmitter to activate the Even Brake #RM-9400 but not the signal from the…

view full answer...

Answer 5

I checked with my tech contact over at Roadmaster and he mentioned that there could be a couple of things going on here that I'll try to address for you. First, you can access the internal components in the Even Brake #RM-9400 system by removing…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Parts Needed for Brakemaster 9000 Where Air Leaks Out of 90 Degree Diaphragm

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching