Battery Box for 2 Group 27 Batteries

Question

Question:

I am looking for a battery box that will fit 2 group 27 12 volt batteries. Do you have something that will work for this? I would like to install it in my travel trailer.

asked by: Tom J

0

Expert Reply:

For a battery box it is going to depend on the dimensions of your group 27, 12-volt batteries. Based on some of the batteries I looked up we have a couple of boxes you could use. First is TorkLift PowerArmor Locking Battery Box # TLA7708R. Attractive, strong, and durable, this is the last battery box you would need.

The dimensions of this box are 26-3/4" long x 8-3/16" wide x 13" tall.

expert reply by: Jameson C

0

Answer 1

What are the other dimensions of the battery?

view full answer...

Answer 2

You are correct that the 10 inch measurement is at the top with the lid on; the width at the bottom is 7-3/4 inches for the TorkLift PowerArmor Locking Battery Box - 6V and 12V Lithium Batteries #TLA7700L.

view full answer...

Answer 3

Hi Mike; the exterior width of 10-1/2 inches includes the lid for the TorkLift PowerArmor Locking Battery Box - 6V and 12V Lithium Batteries #TLA7700L. It is 7-5/8 inches not including the lid.

view full answer...

Answer 4

The TorkLift PowerArmor Locking Battery Box - 6V and 12V Lithium Batteries #TLA7700L weighs approximately 30lbs.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Battery Box for 2 Group 27 Batteries

Product Page this Question was Asked From

Continue Researching