Center to Center Hole Measurement and Diameter of Weight Distribution Shim 58207

Question

Question:

What is the diameter of the holes and the distance between centers of the holes?

asked by: Jon

0

Expert Reply:

Shim # 58207 measures 3-3/4 inches between the mounting holes on center. The holes are approximately 13/16 inches in diameter to accept the 3/4 inch bolts used by the weight distribution hitches for which this shim was designed.

expert reply by: Michael H

0

click to enlarge

Answer 1

Your safety chains should have a maximum gross trailer weight rating, which is what you would need to go by to ensure they are properly rated for your 10,000 lb GVWR trailer. If they are then you can attach them to your Ford hitch; wrapping them…

view full answer...

Answer 2

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 3

Hey Marc, the Lippert 1621 pin box is considered an extended pin box but it's essentially the standard pin box nowadays and doesn't extend past what you have now if you were looking for a way to upgrade. Are you wanting better turning…

view full answer...

Answer 4

It sounds like the gears inside the Demco Autoslide 5th Wheel Trailer Hitch #DM6077 may be off/damaged. I have attached a copy of the instructions which on page 10 show the parts breakdown for the gear mechanism. This will allow you to turn the hitch…

view full answer...

Answer 5

Hi Steven, Thanks for the purchase and we do have the right harness for your 2025 Ram 1500 and the Redarc Liberty Brake Controller #RED24FR. The correct plug-in harness is the following part: - Redarc Plug-and-Play Wiring Harness #331-TPH-020 You can…

view full answer...

Answer 6

Hey Braden, thanks for reaching out. Yes, we do have an anti-rattle device that will work great with your Blue Ox WD setup. The U-bolt style anti-rattle devices are going to give the best results, and for that I recommend the following: - Blue Ox…

view full answer...

Answer 7

There is a wet bolt kit made specifically for a tandem axle trailer with Road Armor equalizers, and includes the shackles, wet bolts, and hardware needed. What you need is the following part: - Lippert AP Kit - Tandem Axle Road Armor Wet Bolts and…

view full answer...

Answer 8

Hello John, thanks for reaching out. For the wet bolts you can measure the overall length or the length not including the head. Honestly when replacing this stuff, the bolts are going to be a standard length and diameter. Typically I would not even…

view full answer...

Answer 9

That's a good question Barry, and electric brakes like #23-468-469 do use 16 gauge wiring for the pigtails. But we do recommend using 10 gauge to connect to the brakes simply because of how far the wiring generally has to be run on trailers. I…

view full answer...

Answer 10

A parking brake system, also known as an e-brake, can only be used if the brake assemblies are already equipped with a parking brake. Dexter does offer electric brake assemblies with a parking brake, but their standard electric brakes assemblies…

view full answer...

Answer 11

The grease zerk fitting on your MORryde 3000 is M6 x 1.0 according to my contact at MORryde. To replace this you need the following part: Replacement Brass Grease Zerk for Weld-On Hinges - #MA35ZR This was designed for a weld-on hinge but since it…

view full answer...

Answer 12

I spoke with my contact at MaxxAir regarding the MaxxAir 2 Vent Covers like the Smoke #MA00-933073 that you were looking at and the Standard Covers like #MA00-933067. He said there are two primary differences between the two models. The first is that…

view full answer...

Center to Center Hole Measurement and Diameter of Weight Distribution Shim 58207

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching