Replacement 1/2 Inch Water Heater Pressure Relief Valve

Question

Question:

Is this the size measured inside the valve? We have a watt series # of 8920. M6-STD-Z2122.

asked by: Patricia

0

Expert Reply:

On the Camco RV Water Heater Temperature and Pressure Relief Valve # CAM10423 the threaded part with the probe is 1/2 inch inner diameter. The similar # CAM10473 is 3/4 inches. Based on your picture you need the 1/2 inch model # CAM10423.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Carl! The only 50' 50A we have with the twist lock connection is the Furrion Faultsmart Marine Power Cord - 50 Amp - LED - Yellow - 50' #381702. The closest option from Mighty Cord is the Mighty Cord RV Power Cord - 50 Amp - 36'…

view full answer...

Answer 2

The difference is the size of the threads. The Camco RV Water Heater Temperature #CAM10423 has 1/2 inch diameter valve size and the #CAM10473 has 3/4 inch diameter valve size.

view full answer...

Answer 3

The Camco Water Heater Element #CAM02143 is what you need for the SW6DEL water heater. According to our research this element will replace the heating element perfectly in your Suburban water heater. You can also use the Camco RV Water Heater Anode…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Replacement 1/2 Inch Water Heater Pressure Relief Valve

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching