What is the Torque Spec for a Nut on a 1-7/8 Inch Hitch Ball

Question

Question:

have a 1-7/8, 2000 lb hitch ball with 1-1/2inch size nut. what foot pound of torque is correct?

asked by: Barry B

0

Expert Reply:

The torque value for your 1-7/8 inch ball is going to depend on the diameter of the shank. Draw-Tite lists the following torque specs:

"During hitch ball installation, torque all 3/4" shank diameter balls to 160 ft. lbs., and 1" shank diameter balls to 250 ft. lbs., and 1-1/4" shank diameter balls to 450 ft. lbs."

expert reply by: Michael H

0

Answer 1

There is an easier solution that a different jack. You can use a longer ball mount so that the trailer, and the jack, will be further away allowing you to lower the tail gate without hitting the jack. Then you could use any jack you wanted. If that…

view full answer...

Answer 2

The correct torque value for the nut on a 1-7/8 inch hitch ball depends on the diameter of the shank. Draw-Tite, who makes #19256 and #19260 lists the following torque specs: "During hitch ball installation, torque all 3/4" shank diameter…

view full answer...

Answer 3

Yes you can torque the nut of the Curt hitch ball part #C40034 to 250 ft lbs with the ball and ball mount installed in the vehicle's hitch.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi Richard! From the top of the shank to the lowest part where the tri-ball sits on the #BWTS20067BMP is 11.125". If you have the balls at max drop with the tallest one hanging down that would be 12.5". We recommend at least 11" of…

view full answer...

What is the Torque Spec for a Nut on a 1-7/8 Inch Hitch Ball

Product Page this Question was Asked From

Continue Researching