How to Make a 40 foot Long RV Black Water Dump Hose

Question

Question:

Hi, I need a black water dumping hose . I need it to be 30 to 40 feet long. I see that you have a kit that includes two 10 foot hoses that conect together but, I need it to be linger. Do you have a 40 foot hose ot two 20 foot hoses that I can connect together? I like the sturdy one that wont be ruined if it is stepped on. Can you help me?

asked by: Kerry B

1

Helpful Expert Reply:

To give yourself 40 feet total of sewer hose you would need two of the # CAM39611 which are 20 feet long and then to connect them you would need the coupler part # CAM39203.

For a 4 in 1 adapter to use on the hose you would need the part # CAM34971 as well.

expert reply by: Jameson C

1

Jerry J.

7/22/2020

It is a pretty long distance from the end of my driveway to my sewer cleanout. How long of a sewer hose can I make to clean the tank at home. My guess is that it is about 75 feet from the end of the driveway to the sewer cleanout, and it is down hill.

Dustin K.

8/10/2022

@JerryJ did you figure out how to get a custom long hose I need 50 foot and looking for any suggestions.. I found the connections for both ends just need the custom hose that's durable? Thank you

David B.

8/11/2022

The longest hose I have is the Camco HTS Heavy Duty RV Sewer Hose - Brown - 20' Long # CAM39631. It is also the thickest hose I have about 23mm thick. I also have a 10ft hose Camco RhinoFLEX RV Sewer Hose - Brown - 10' Long # CAM39671. Instead of getting two 20s and one 10, I think the best route would be to get 3 of the 20foot hoses and cut it to size after you splice it together. You may be able to source a 50ft hose from a plumbing specialty store though. I would find/call one first or even ask a plumber if they know where you could find a hose that long.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

How to Make a 40 foot Long RV Black Water Dump Hose

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching