New Hub/Drums Grease Instructions w/ Older Nev-r Adjust Brakes
Published 07/27/2016 >
Products Featured in This Question
Question:
Just bought four of your hub/drum assemblies for 5,200 - 6k axles 23-459. Im installing them over Nev-R adjust brakes 23-459 which have seen about 5,000 miles. Do I need top preload the new bearings? Is it necessary to do anything to the oldfoot shoes and magnets with the installation of new drums? One of the seals on an old drum was bad and theres traces of grease on the magnet and shoes - can I just give them a good dose of Brakleen or should I replace the backing plate assembly?
asked by: Jeff N
Expert Reply:
Here's how to grease everything upon initial installation.
First, grease your bearings and spindle by hand or with a bearing packer like part # L70025. If you are going to do it by hand, start with a gob of grease in your palm and then press the bearing into the grease with some force.
Next, insert your bearings and grease seal in the hub and mount your hub on your spindle. You should slowly pump grease into the spindle. As you are pumping the grease into the spindle, occasionally rotate the hub. This will prevent the grease from building up in one spot.
Continue to pump grease until you begin to see the outer bearing move or you see grease seeping through the outer bearing. If you pump the grease slowly and rotate the hub, you should not blow the grease seal. Once you see the grease seeping through, you can install the washer, spindle nut and nut retainer. Keep in mind, when threading on the castle nut, you will want to tighten the nut until it is hand tight and then slightly back it off.
I attached a video on packing bearings for you to check out as well.
Some brake parts cleaner will take care of the grease on your old assemblies as well.
Product Page this Question was Asked From
50MM Nev-R-Lube Trailer Wheel Bearing for 8,000-lb Dexter Axle - Qty 1
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 50 MM I.D.
- Bearing 31-71-3
- 8000 lbs Axle
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Shop: Mounting Bolts and Hardware for 12" Brake Assemblies
- Shop: Brake Mounting Bolt for 12" Brake Assembly
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 6K
- Q&A: How to Initially Adjust Dexter Nev-R-Adjust 12 x 2 Electric Drum Brakes 23-458 and 23-459
- Q&A: What Brake Replacements Do You Recommend for My Dexter 5200 Pound Axles?
- Shop: Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Shop: Brake Controller
- Search Results: trailer jack
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Gooseneck Hitch
- Search Results: trailer lights



