Inside Knob For Redline Stainless Steel Flush Door Latch

Question

Question:

Can you buy an inside release for this? If so, how can you get one?

asked by: Russ

0

Expert Reply:

The Steel Flush Door Latch, part # N3980 has a threaded hole on the back side that would be in the inside of the door.

I called my contact at Redline and the knob that can be used on the inside of the door is part # 4PLSP.

expert reply by: Jeffrey L

0

Answer 1

It sounds like the lift arms aren't able to keep the lid up to the fan's fully-opened height. There are a few things that may cause this. You may have already tried this, but push the manual knob in when the you've reached the…

view full answer...

Answer 2

I don't have any way of looking up what specific locks were used on your Forest River 16BHS, but I can say that Global Link provides most of the entry door lock sets for later model RV/Campers. The lockset fits doors that are 1-1/4" to…

view full answer...

Answer 3

We have the Non-Locking Steel Flush Door Latch, part #N3980 in stock, but there are a few changes you need to be aware of. I have attached a couple photos that show the difference between the latch shown on our website and what we actually have. I…

view full answer...

Answer 4

The easiest way to find a replacement is find the dimensions of the hole that the latch sits it.The Flush Locking Stainless Steel Latch, part #L1833. The latch fits in a 2-3/4 inch by 3-3/4 inch hole and features an inside release. The larger #L3980…

view full answer...

Answer 5

Typically, the Junior Door Latch would install by routing or cutting out a 2-3/4 by 3-3/4 inch hole and would then either be bolted or riveted to the door through holes that would need to be drilled in the flange around the latch. The latch is meant…

view full answer...

Answer 6

If you instead went with the Junior Latch part #L1883 you could then use the knob part #4PLSP but there isn't a knob solution for the #N1980.

view full answer...

Answer 7

I went out into our warehouse to measure the "Junior" Non-Locking Steel Flush Door Latch #N1980 and found that overall it is 4-1/2 inches long, 3-3/4 inches wide and 1-1/2 inches deep.

view full answer...

Answer 8

I spoke to my contact at Redline and he informed me that the maximum thickness for the panel that you could install this Junior Door Latch #N1980 on would be 3/4 of an inch. Basically, this and the Full Size Door Latch #N3980 that you referenced have…

view full answer...

Answer 9

Sounds like you are looking for something like the Locking Stainless Steel Flush Door Latch #L3980 as this is the common door latch you see on the side doors of enclosed trailers and can be used on doors that are 1 inch thick like yours.. I attached…

view full answer...

Answer 10

To install the handle will require you to drill holes along the lip of the door latch. I went out to our warehouse to get the dimension you are looking for and found that when the latch is pulled up it will stick up 1 inch above the housing.

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Inside Knob For Redline Stainless Steel Flush Door Latch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching