See what our Experts say about this Redline Trailer Door Latch

• How Far Past The Edge Does The "Junior" Locking Steel Flush Door Latch # L1930 Extend?
  As I see you were looking at the "Junior" Locking Steel Flush Door Latch # L1930 I can tell you the latch is going to stick past the edge of the latch by 3/8". This measurement is going to be past the edge of the cutout portion by 7/8" if that is where you are measuring from.
  view full answer...
• Replacement Tack Room Door Latch for CM Dakota Horse Trailer
  It would appear that your CM Dakota horse trailer uses a door latch like the Locking Steel Flush Door Latch with Inside Release # L1930. I have included an image with the measurements for this latch. Please let me know if your latch is different than these measurements.
  view full answer...
  
• How to Mount Junior Door Latch # L1930
  Typically, the Junior Door Latch would install by routing or cutting out a 2-3/4 by 3-3/4 inch hole and would then either be bolted or riveted to the door through holes that would need to be drilled in the flange around the latch. The latch is meant to be used in doors up to 3/4 inch thick. Because the latch is a universal fit item with many different mounting possibilities, the mounting holes are not pre drilled and mounting hardware is not included. If you would prefer something with...
  view full answer...
  
• Fitment and Compatibility of Replacement Lock Core for Tack Room on Horse Trailer
  Thanks for your picture. The lock you were looking at is designed by a tool box company, UWS, but it might work for your latch depending on the dimensions. Best thing is to measure. The # UWSLOCKCH501 has a diameter of .626 inches and length from under the lock head to the end of .676 inches when measured with a caliper like # PTW80157. I was able to find a replacement key and tumbler set for a latch lock more like the one in your picture. This new tumbler set # CHKT fits lock models...
  view full answer...
  
• Replacing a Junior Locking Steel Flush Door Latch with Inside Release
  It depends on how the old one is attached to the door but you will likely have to pry it off. If there are no visible fasteners there wouldn't be any other way. You would have to be very careful not to damage the door in the process. When installing the new one I would put a screw in each corner which will require drilling the holes for the screws. Typically, the Junior Door Latch would install by routing or cutting out a 2-3/4 by 3-3/4 inch hole and would then either be bolted or riveted...
  view full answer...
  
• Replacement Keys to Tack Room of 2003 CM 2 Horse Slant Trailer
  The # CHK510 key you mentioned is common to all # L1980, # L1930, # L1883, # L1833, and # L4080 latches. In order to get you the correct key, look on the face of the lock and see if there's a reference number engraved or stamped next to the key slot. That number might help me find you a replacement key, if you can reply and let me know what the number is. Otherwise, if you can provide the dimensions of the rough opening the latches sit in, I can recommend replacement locks for you. Replacement...
  view full answer...
• Replacement Locking Flush Door Latch with Inside Release
  All the flush mounted latches we offer are pretty similar, with the differences being size of the hole they install in, the way the metal of the latch is finished, and whether they lock or not. To determine which latch you need, the best place to start would be to remove the latch and measure the hole it's mounted in. The 'Junior' latches mount in a 2-3/4 x 3-3/4 inch hole. The full sized latch uses a hole 3-3/8 x 4-5/8. I'm not entirely sure what the 'inside mounting' dimensions you...
  view full answer...
• Locking Trailer Door Latch with Inside Release for a 1 Inch Thick Door
  You can use the full-size locking door latch # L3980 for doors up to 1-1/16 inches thick. To add an inside release you will just need to add # 4PLSP.
  view full answer...
• Is There Recommended Mounting Hardware for Junior Flush Door Latch
  Hey Fitz, we don't have recommended hardware for the Junior Latch part # L1930 but we can still help. This latch doesn't even have holes drilled in it so you would need to do that in the correct size so that you could either rivet or bolt the latch into place. That would really depend on your application so it really comes down to you coming up with what would work best for you. I've even seen one guy weld this latch on...which way are you leaning?
  view full answer...
• Can The Junior Locking Steel Flush Door Latch Be Keyed Alike?
  I called my contact at Redline, and they told me that they use the same lock and key for their flush mount door latches. So you could order 3 of part # L1980 and they would all be keyed alike. This latch has a stainless steel spring and a rustproof finish. The mounting hole size needed for this latch is 2-3/4 by 3-3/4 inches. If you determine you need a different size, as long as you order the Redline product, any number of the same item number will be keyed alike for their door latches. I...
  view full answer...
• Availability of Keyed-Alike Lock Cores for Locking Stainless Steel Flush Door Latch
  Locking Stainless Steel Flush Door Latch # L1833 from Redline can be re-keyed with a new tumbler and key set by using part # CHKT. This new tumbler set fits lock models # L1980, # L1930, # L1883 and # L1833. I verified this with my contact at Redline trailer supply.
  view full answer...
• Installation of the Junior Locking Steel FlushDoor latch, Item # L1930
  The Junior Locking Steel Flush Door Latch with Inside Release, item # L19730, is designed to fit through a 3/4 inch thick, or less door. At this time we do not carry door kits for enclosed trailers but we do carry hinges, door holders and other parts (see link) for enclosed trailers.
  view full answer...
• Replacement 4-3/4 inch Long Flush Latch on Horse Trailer
  Based on the dimensions you listed the correct replacement latch would be part # L1930 which is a junior size latch. This has the knob on back side of the latch. For one that has a flat back you'd want the part # L1883.
  view full answer...
• Can Redline Junior Locking Steel Flush Door Latch be Keyed Alike
  According to our contact at Redline, they use the same lock and key for their flush mount door latches like the Junior Locking Door Latch # L1930 referenced in your question. If you decide to order 8-10 of these latches, they will all be keyed-alike. This will mount in a 2-3/4 inch x 3-3/4 inch hole. I have attached a short video demonstration on this product for you to check out.
  view full answer...
• Replacement Key and Tumbler Assembly for Redline "Junior" Locking Steel Flush Door Latch # L1930
  We have what you need. The replacement Key and Tumbler Set for the Redline "Junior" Locking Steel Flush Door Latch # L1930 is part # CHKT. This kit includes one tumbler and one key.
  view full answer...
• Can Junior Locking Steel Flush Door Latch with Inside Release # L1930 be Keyed Alike
  I called my contact at Redline, and they told me that they use the same lock and key for their flush mount door latches. So you could order 3 of part # L1930 and they would all be keyed alike.
  view full answer...

Do you have a question about this Trailer Door Latch?