Replacing OEM Brake Controller On 2016 Toyota Tundra

Question

Question:

I have a 2016 Tundra with the OEM integrated brake controller. It appears to have no to un-noticeable gain in the electric mode. The truck is scheduled to go to the dealer for them to take a look at it. This same problem has been reported by others on Tundratalk.net without any reported resolution. In that I need a working brake controller in the next few weeks, I just as well go with the P3 and be done with it. Have there been any conversion problems that you are aware of for the 2016 Tundra going from the OME to the P3? Thanks,

asked by: Larry G

0

Expert Reply:

I called my contact at Tekonsha about your 2016 Tundra and the OEM brake controller. They have not received any bulletins or information about the OEM controllers. We have not had the opportunity to install a brake controller on a 2016 Tundra that has an OEM controller already installed.

They told me that you may have to get the computer 'flashed' in your Tundra at the dealership when you remove the OEM and replace it with the P3, part # 90195. This is a discussion you would need to have with your dealership. We also have the plug-in adapter, part # 3031-P that plugs into the built-in port behind the dash of your vehicle.

I do agree it needs to be addressed for safety concerns and with the new truck should be a priority at the dealer.

expert reply by: Jeffrey L

0

Answer 1

You can correct the error message on your Tundra dash caused by installation of your aftermarket Prius IQ brake controller #TK90160 by disconnecting the battery + cable for about 5 minutes. Once you reconnect it the error could should be cleared from…

view full answer...

Answer 2

The Prodigy P3 item #90195 is compatible with your 2017 Toyota Tundra. This is a proportional brake controller that activates your trailer's brakes when your Tundra decelerates. You will want to use the Custom Wiring Adapter for Trailer Brake…

view full answer...

Answer 3

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 4

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 5

I wasn't able to locate your specific order, but it looks like you are referring to the Tekonsha Prodigy P3 Brake Controller #90195 (excellent choice) and the Plug-In Adapter #3031-P. If this is correct, these are indeed the correct parts and all…

view full answer...

Answer 6

I recommend using the Tekonsha Prodigy P3 #90195, because it's going to provide you with an easy to read LCD screen and provides you with reliable proportional braking for your trailer. The Prodigy P3 automatically levels when mounted within a…

view full answer...

Answer 7

I understand your confusion! The OEM trailer brake controller connector for your 2016 Toyota Tundra is located behind the small panel on the right side of the steering wheel as shown at the 9:20 mark of the included video. This plug will be currently…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hello Joe, Thanks for writing in! Based on the measurements you provided, the Gen-Y Glyder Shock Absorbing Ball Mount #325-GH-12001 is not the right fit for your setup. Since your Tundra's receiver measures 18 inches from the ground and your TAB…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Replacing OEM Brake Controller On 2016 Toyota Tundra

Continue Researching