Recommended Brake Controller and Plug in Adapter for a 2017 Toyota Tundra

Question

Question:

Hello, need a brake controller for my 2017 crew max tundra. Been reading….the P3 is not compatible?

asked by: Armando M

0

Expert Reply:

The Prodigy P3 item # 90195 is compatible with your 2017 Toyota Tundra. This is a proportional brake controller that activates your trailer's brakes when your Tundra decelerates.

You will want to use the Custom Wiring Adapter for Trailer Brake Controllers item # 3031-P to complete your installation without cutting or splicing wires.

expert reply by: Jerred H

0

Answer 1

Yes you can replace the factory brake controller of your 2017 Toyota Tundra with the Prodigy P3 part #90195. You would just need the correct install harness part #3031-P to plug the P3 in place of the factory controller.

view full answer...

Answer 2

You can definitely ground your trailer brake assemblies to your trailer frame. This will be just as effective and also will be a much easier install.

view full answer...

Answer 3

The correct brake controller install harness for installing the Prodigy P3 brake controller part #90195 in your 2017 Toyota Tundra is the part #3031-P.

view full answer...

Answer 4

The brake controller connector is clipped to the back side of a panel located just to the right of the ignition key. You'll need to lower the panel and unclip the connector from the rear of the panel, then feed it down behind the panel so it…

view full answer...

Answer 5

To wire your electric brakes you will want to run 10 gauge wire #10-1-1 to one of the brakes and run it to the other brake, using butt connectors like #05732-2 to connect them. The grounds will not be spliced, each brake assembly should have its own…

view full answer...

Answer 6

The first step I suggest for troubleshooting your truck's trailer brake controller is to disconnect the truck and trailer and clean the connectors. If that does not correct the problem, test using a circuit tester like #PTW2992. See the linked…

view full answer...

Answer 7

To install the Tekonsha P3 into your 2008 Tundra with the factory 7-way, you'll need the #3040-P wiring harness which plugs into the factory connector behind or above the driver's side kick panel. As long as your Tundra has the factory tow…

view full answer...

Answer 8

Electric brakes have 2 wires located at the back. One is for power and the other is for ground (it doesn't matter which is used for which function). The ground wires should be connected to the trailer frame. The only other place that would carry…

view full answer...

Answer 9

If you have a 7-Way on both your trailer and tow vehicle you will first want to make sure that you have a brake controller, like the Tekonsha Prodigy P3 #90195. A brake controller is what is used to send power from the tow vehicle and tells the…

view full answer...

Answer 10

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

I wasn't able to locate your specific order, but it looks like you are referring to the Tekonsha Prodigy P3 Brake Controller #90195 (excellent choice) and the Plug-In Adapter #3031-P. If this is correct, these are indeed the correct parts and all…

view full answer...

Recommended Brake Controller and Plug in Adapter for a 2017 Toyota Tundra

Continue Researching