Trailer Jack Recommendation for a Triton Jet Ski Trailer

Question

Question:

Hi: I need to buy a tire jack to use on my Triton Jetski Trailer LTWCI. What do you recommend? Thanks,

asked by: Joe S

0

Expert Reply:

Sounds like you are looking for a trailer jack for your Triton Jet Ski trailer that has a caster wheel on it to make it easier to move around by hand.

The most popular option we offer that would fit your trailer well is the Pro Series jack part # PSEJ10000101. I looked up pictures of your trailer and the mounting bracket of this jack would work well on your trailer.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Hey Dave, Looks like the BT-150 uses #L44649 bearings so you would be able to swap the hub out with the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-G-EZ-2K. This comes with a #10-9 grease seal, which has a 1.5" inner…

view full answer...

Answer 2

Hey Bruce, it sounds like you might have some older seals, perhaps Transcom seals with the 1.983" OD. We do have one seal, the #10-9 seal, which has proven to be a suitable replacement for these seals. This is a double lip seal with a 1.5"…

view full answer...

Answer 3

Based on the number and dimensions you listed the correct grease seal you need is the part #RG06-020 as this cross references to what you have and matches the dimensions.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Trailer Jack Recommendation for a Triton Jet Ski Trailer

Featured Help Information

Miscellaneous Media

Continue Researching