Compatibility of Curt Locking Pins on Curt Adjustable 2-Ball Mount C45902

Question

Question:

Can you use the Curt Locks - C23556 for this unit?

asked by: Amal J

0

Expert Reply:

Yes, the Curt locking pins # C23556 will work great for the Curt Adjustable 2-Ball Mount # C45902.

I was able to go out to the warehouse and confirm the fit for you.

expert reply by: Jackie C

0

Answer 1

There is indeed a locking hitch pin set, part #C23556. This part number includes two locks, one hitch pin lock and one locking pin that would replace one the retaining pins that keeps the ball assembly in place. The locks are keyed alike.

view full answer...

Answer 2

The raised square plates on shank of the Curt Adjustable 2-Ball Mount part #C45902 are present on older versions of the ball mount but not all. The new version of this ball mount has the smooth shank like you have mentioned. The version of this ball…

view full answer...

Answer 3

There are 3 places of possible movement for Curt adjustable ball mount #C45902: the 2 pins that hold the ball to the shank and between the shank and the hitch itself. If you have that screw at the ball part nice and tight then you are probably…

view full answer...

Answer 4

It sounds like the InfiniteRule Locking Pins #IR39FR will be the best option for your adjustable ball mount. This kit includes two 4-5/8" inner span locking pins and one 3-1/8" inner span locking pin for securing the hitch to the receiver.…

view full answer...

Answer 5

Yes, the Curt Lock Set #C23556 will work with both the #C45900 and #C45902 meaning the 2-1/2" hitch won't be a problem. The pair of locks comes keyed alike but there is no option to match the keys between the sets of locks.

view full answer...

Answer 6

Yes it will! The Rubber Bumper #C45921 is a direct replacement for the Curt Adjustable Ball Mount #C45900 but the only differences between the shank that comes with that system and the Replacement Shank #C45917 that you referenced is the weight…

view full answer...

Answer 7

For Curt adjustable ball mount #C45902 the locking pin set is #C23556. The pins don't have an official capacity but technically 5/8 inch diameter solid steel is going to have a capacity much higher than the hitch or vehicle. The hitch pin has a…

view full answer...

Answer 8

The Curt Adjustable 2-Ball Mount #C45902 is manufactured overseas. If you are looking for a similar made in the USA adjustable ball mount the Flash Solid Steel HD Adjustable 2-Ball Mount #FA49-00-5625 has the same 2-1/2" receiver, 6" drop,…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Compatibility of Curt Locking Pins on Curt Adjustable 2-Ball Mount C45902

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching