What Does the CE Smith U-Bolt Kit for Mounting 1-1/2" Square Trailer Axles # CE23102 Come With

Question

Question:

does it come 2 or 1

asked by: Juan M

0

Expert Reply:

The CE Smith U-Bolt Kit for Mounting 1-1/2" Square Trailer Axles # CE23102 that you referenced includes two u-bolt plates, 8 nuts and washers, and 4 u-bolts. In other words it comes with two sets and not just one like you asked.

expert reply by: Jameson C

0

Answer 1

For a slipper spring that would work well for your application you would want the part #e29SR. This is a 2k rated spring that is 30-1/4 inches long. This should be a much softer spring than what you have as it looks like your spring would be a higher…

view full answer...

Answer 2

Installing the U-bolts and plate like that would be fine, but I would recommend putting the plate on the leaf springs and running the U-bolts around the axle instead. The good news is you're replacing them so you can make that change when you…

view full answer...

Answer 3

We have a few options for 30 inch long slipper spring that is 1-3/4 inches wide. For a 3,700 lb axle option we have the part #SP-040275. For a 2,900 lb axle option we have the part #SP-039275. For an 1,800 lb axle you would want the part #e29SR.

view full answer...

Answer 4

The closest leaf springs we have to what you're describing is part #e29SR. these are 30 inches from the center of the eye to the very end of the slipper end. One thing to keep in mind is your springs are going to be longer than they were when…

view full answer...

Answer 5

Yes the slipper spring part #e29SR that you referenced can install below the trailer axle. I attached a picture that shows it installed in this orientation.

view full answer...

Answer 6

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

What Does the CE Smith U-Bolt Kit for Mounting 1-1/2" Square Trailer Axles # CE23102 Come With

Product Page this Question was Asked From

Continue Researching