Lens Replacement Recommendation for Optronics Light STL8RB

Question

Question:

The new Optronics LED taillights that I got from you for my trailer are great, BUT I managed to crack one of the side marker lenses. Can I get 2 of those from you? Thanks!

asked by: Joseph R

0

Expert Reply:

Yes we carry replacement side lenses for the part # STL8RB and # STL9RB. For that you would want the part # AL9RB.

For a replacement front lens you would want the part # A8RB.

I was able to check your order notes to determine that you ordered the # STL8RB.

expert reply by: Jameson C

0

Answer 1

The reason there are trailer light kits listed for under 80 inches and over 80 inches is that there are different lighting regulations for vehicles that have widths that are larger than 80 inches in width than ones that are less than 80 inches wide.…

view full answer...

Answer 2

Thank you for the picture that is very helpful since I cannot always see what trailer manufacturers used on their trailers. The LED Combination Tail Light Kit #TLL9RK may be your best option depending on the condition of your current wiring. This kit…

view full answer...

Answer 3

We have just what you are looking for. I recommend the LED Submersible Trailer Stop, Turn and Tail Light, part #STL8RB. This is for the right side of the trailer and is a stud mounted LED light. It has the side marker light that illuminates when the…

view full answer...

Answer 4

The passenger side equivalent of the Combination LED Trailer Tail Light #STL9RB is the #STL8RB. This has all of the same functions aside from the license plate light.

view full answer...

Answer 5

The reason that the Passenger Trailer Tail Light #STL8RB has 11 diodes and the Drivers Side #STL9RB has 14 diodes is because the driver side light has an additional function; license plate illuminator. This is why you see a difference in the amount…

view full answer...

Answer 6

If you want a submersible tail light I would recommend the LED Submersible Trailer Stop, Turn and Tail Light, 6-Function, 11 Diode, Right Hand, part #STL8RB. The #STL28RB you referenced is not submersible, and I would not recommend it if you need a…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Lens Replacement Recommendation for Optronics Light STL8RB

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching