Compatibility of Hopkins 7-Way # HM47210 With # 41157 Gooseneck/Fifth Wheel Wiring Harness

Question

Question:

will part #HM work with part #41157?

asked by: Brandon F

0

Expert Reply:

It sure would. The Pigtail of the # HM47210 unplugs from the pigtail, and the # 41157 would plug inline between the pigtail and the 7-way connector as shown in the photo I've edited for you.

If you click the provided link, you can see the # 41157 being installed on a 2011 Ram truck.

expert reply by: Mike L

0

click to enlarge

Answer 1

The great things about the 50MM Nev-R-Lube Bearing for 8,000-lb Dexter Axles part #31-71-3 is they do not require grease. They are a bearing, race and seal built into one pre-greased from the factory. You can use a very small amount of anti-seize…

view full answer...

Answer 2

In order for the trailer brake magnets to get full adhesion to the inside armature surface of the brake drum, the magnet face and the armature surface of the drum need to be perfectly flat and smooth. Since they aren't mating together perfectly,…

view full answer...

Answer 3

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 4

Basically you would just need to run everything including the generator to the trailer battery as this will ensure that when the generator is running it would be powering everything as well as charging the battery but when the generator isn't…

view full answer...

Answer 5

According to Dexter Axle, the attachment bolts for a 12 x 2 brake assembly should be torqued to 25-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 6

When it comes to checking the armature surface on your hub and drum assembly like the Dexter #84556UC3 there is no specific measurement related to the back of the lugs that indicates wear. What you are looking for is grooves or discoloration and…

view full answer...

Answer 7

I would check the magnets for wear before going on to test them with a meter. If the magnets show abnormal wear or if you can see the windings beginning to show through the friction surface of the magnet then they will need to be replaced. To further…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Compatibility of Hopkins 7-Way # HM47210 With # 41157 Gooseneck/Fifth Wheel Wiring Harness

Featured Help Information

Miscellaneous Media

Continue Researching