What Do You Use to Mount Plastic Fenders to a Tow Dolly

Question

Question:

Hi i have a Master Tow dolly and need some replacement fenders. I was looking for some plastic fenders. I was just wondering how i would go about mounting the plastic fenders to my dolly. The dolly has two studs on each side to mount typical steal fenders. Thanks

asked by: David M

0

Expert Reply:

Usually customers will use a couple of L-brackets, such as # PF775-BKT-2, to mount a replacement fender. You would need to drill holes in the fender so the studs on the trailer can go through. Then attach the brackets. I included a picture showing an example.

You don't have to bolt through the top of the fender like in the picture. That is just one way it can be done. If the plastic fenders have steps like # F008574 the steps would cover where the brackets attach to the fender so you wouldn't see it.

expert reply by: Michael H

0

click to enlarge

Answer 1

Yes, the narrower ST205-75R14 tire will fit in place of an ST215-75R14, It is important for all of the trailer tires to be the same size and construction type (bias ply or radial). Using different sizes can cause tracking problems and lead to…

view full answer...

Answer 2

There is only a very slight size difference between the ST215/75R14 and the ST205/75R14 that you currently have on your trailer. The difference is less than half an inch in overall diameter less than half an inch in additional width. You would want…

view full answer...

Answer 3

Radials are the way to go for highway use like you said you'd be using your dolly with. For a 13 inch trailer tire that's a radial the Karrier Tire part #AM10210 which is a size ST175/80R13 would be a great option. It has a capacity of 1,610…

view full answer...

Answer 4

A tire's weight rating is per tire. For example Roadmaster Tow Dolly with Electric Brakes 4,250 lbs #RM-2050-1, uses #RM-200330-80 tires which has a maximum load capacity of 1,570 lbs each. With 2 tires used, the load capacity of the tires…

view full answer...

Answer 5

You can pretty easily go from a 205/75-14 to a 15 inch tire size like 205/75-15 like with the #AM32395 without clearance issues. This will give you a slightly larger wheel and tire which will have a higher weight capacity. So you might gain a slight…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

What Do You Use to Mount Plastic Fenders to a Tow Dolly

Product Page this Question was Asked From

Continue Researching