How Do You Remove the Bump Stops on a 2015 Mercedes Sprinter 3500 to Install Timbren Springs

Question

Question:

I am looking at your TMBFSP35 axle stops to reduce the sway on my Solaris R24. It looks like the original axle stop is completely captured at the top. I was wondering how you remove the original axle stops? I appreciate any information or advice.

asked by: Jon L

0

Expert Reply:

The factory bump stops on your RV built on a 2015 Mercedes Sprinter 3500 chassis will have to be cut off and the captured part pushed out in order to install Timbren rear helper springs # TMBRSP35B. There really isn't any other way based on your picture.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Tekonsha Prodigy RF Wireless Trailer Brake Controller w/ Bluetooth item #TK94FR has to be securely mounted to your trailers coupler with screws. The Prodigy RF connects to your vehicles 7-way so there aren't really any alternatives to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hi Todd, I know exactly the feeling you’re describing, and you’re definitely not alone. That floaty, pushy feeling at highway speeds, especially when trucks pass, is really common on the Sprinter 3500 chassis with a taller coach like your Tiburon,…

view full answer...

Answer 9

If your 2021 Mercedes-Benz Sprinter 3500 is a van then yes, the Roadmaster Rear Anti-Sway Bar #RM43VR is the only compatible option. If your 2021 Mercedes-Benz Sprinter 3500 is a Class C motorhome then you also have the option of the Roadmaster Rear…

view full answer...

Answer 10

Hi Gary, I completely understand why you’re hesitant to just pour this into your fresh tank. Since BluTech’s site says to call if you do not have the filtration system, it makes sense that you would want a clear and safe way to use it. The Blu…

view full answer...

How Do You Remove the Bump Stops on a 2015 Mercedes Sprinter 3500 to Install Timbren Springs

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching