Horizontal Length of the Replacement Upright CE27608PG

Question

Question:

Hello, can you tell me the dimensions of this part? I know it is 18inch tall and 1.5inch square but what it is the length of the other part of the tube? Thanks!

asked by: Bob

1

Helpful Expert Reply:

I went out into our warehouse to grab a part # CE27608PG and found that the other dimension you are looking for is 17 inches.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The short leg of the CE Smith #CE27648 Post-Style Guide-Ons measures 21-1/2 inches from the end of the leg to the inside edge of the upright and 23 inches to the outside of the upright. I've shown these dimensions in the provided photo. CE Smith…

view full answer...

Answer 2

There is an upright which may work for you, the Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - Lanced - 39" #CE27605PG. This upright has a bottom leg of 23 inches, and is a replacement for CE Smith Post-Style Guide-Ons…

view full answer...

Answer 3

It looks like you might be looking for the CE Smith Post-Style Guide-Ons for Boat Trailers - 60" Long - I-Beam Clamps - White - Qty 2 #CE27648, which are a 60" post style guide on that are white in color.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Horizontal Length of the Replacement Upright CE27608PG

Product Page this Question was Asked From

Continue Researching