Dimensions Between Mounting Holes for Door Plunger and Socket

Question

Question:

On the PLR64-66 Door plunger and socket What is the on center distance between the mounting holes for each piece? Thank You

asked by: Steve

0

Expert Reply:

I went out to the warehouse and pulled the # PLR64-66 and took some measurements for you. The dimensions from center to center of the mounting holes on the plunger is 2 inches and on the socket it is 2 inches center to center.

I also made an image of the part showing these measurements for your reference and attached a product demonstration video too.

expert reply by: Chris O

0

click to enlarge

Answer 1

We have just what you need. What you are referring to is a door plunger like part #PLR64-66. The male end mounts on the door and the female socket mounts on the trailer wall and when needed it can hold the door open.

view full answer...

Answer 2

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 3

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 4

Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…

view full answer...

Answer 5

It sure is Barry! The SoftStartRV Soft Start item #SSR54FR is exactly what you need for a Furrion AC unit. It'll lower the amps required during startup so you can run other appliances at the same time or power your Grand Design off of a…

view full answer...

Answer 6

The length of a fender is measured from the longest point, at the very bottom of each end across. Then the height is measured from the tallest point, right in the center. For example, the CE Smith Single Axle Trailer Fender #CE17720 is 22-1/2"…

view full answer...

Answer 7

Hello Kristen, The CG Convert-A-Ball Multi-Cushioned Gooseneck Coupler #CG is your best option to replace the inner tube on your older Bulldog gooseneck hitch. What makes it so great is that it doesn’t need a load-bearing pin to work. Since your…

view full answer...

Answer 8

You need a breakaway battery charger if you want to maintain the battery charge on your breakaway kit using your tow vehicle's 7-way trailer connector. The 12 volt battery on breakaway kits, like all batteries, will self-discharge over time.…

view full answer...

Answer 9

You will be able to use a inner tube like the Convert-A-Ball Multi-Cushioned Gooseneck Trailer Coupler #CG that also does not have the holes for the pin. This particular tube has the cushioned coupler to help reduce road shock from the trailer into…

view full answer...

Answer 10

I was able to pull up one of your old orders (thank you for being a loyal etrailer.com customer!) and it looks like you've previously purchased the LaSalle Bristol Toilet Floor Flange for RV - ABS Plastic - 3" Hub x 4" Diameter…

view full answer...

Answer 11

I recommend using the Tow Ready 5th Wheel/Gooseneck Wiring Harness #20110-010 for your 2019 Ford F-250 Super Duty because it comes with both steel and aluminum screws. Since you have an aluminum bed you'll use the aluminum screws and they…

view full answer...

Dimensions Between Mounting Holes for Door Plunger and Socket

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching