Can 1-1/4 Inch Factory Hitch on 2010 Ford Escape Be Removed to Install 2 Inch Hitch
Question:
I have a 2010 Ford Escape with a 1 -1/4inch hitch that I think came on the vehecle. I want to replace it with a 2inch class III hitch, either Draw tite or Curt Can you just remove the class II hitch and put the class III 2inch hitch on in its place? Thanks for any info you can give me.
asked by: John W
Expert Reply:
I have some good news for you! The Curt # C13651 and Draw-Tite # 75751 will install on your 2010 Ford Escape without having to remove the factory hitch. I have attached the installation instructions, a video, as well as a picture to illustrate how this will look once on your vehicle. Please keep in mind that both hitch receivers will still be functional but should not be used at the same time. Using both receivers at the same time could overload your vehicle and cause damage.
As for removing the factory hitch, as long as it was a bolt-on application you shouldn't have any problems removing it if you chose to. Alternate mounting instructions are listed for vehicles without the factory hitch.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5250 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Video: Install: Curt Trailer Hitch Receiver on a 2009 Ford Escape
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Differences between the Curt Trailer Hitch # C13651 and # 13650 for a Ford Escape
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Finding the Right Trailer Wiring Harness
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Article: My Trailer Hitch Doesn't Fit
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Mount: etrailer Trailer Hitch Receiver on a 2024 Subaru Crosstrek
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: hitch
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Q&A: Do I Need to Trim to Install a Hitch on a 2024/2025 Chevrolet Equinox EV?
- Search Results: trailer hitch ball mount
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Roof Rack
on Trailer Hitch
