Replacement Lid Parts for Sears X-Cargo Sport-20 Rooftop Cargo Box

Question

Question:

We need a replacement lid lifter hinge for our X-Cargo Sport-20 car top carrier. Do you all have a recommendation? Thank you!

asked by: Paul K

0

Expert Reply:

We do offer a replacement Spring Hinge for the Sears X-Cargo Sport-20 rooftop boxes, part # TH14933. The part # TH14936 you referenced is not an ideal fit for your Sears X-Cargo Sport-20 due to the stiffness of the spring.

expert reply by: Adam R

0

Answer 1

If you are looking for replacement spring hinges for your Sears X-Cargo box, you will need a Replacement Spring Hinge #SR03810 for your single broken hinge. I went ahead and attached a picture of a Sears X-Cargo Box that has both hinges replaced with…

view full answer...

Answer 2

The difference between the Thule hinges or struts #TH14936 and #TH14933 is the spring tension. Both of these hinges will work for your Sears X Cargo Sport 20 lid. However, the #TH14936 includes better springs.

view full answer...

Answer 3

We do in fact have the replacement hardware for your Sears X-Cargo carrier. You will need the Replacement Hardware Kit for Searsbox Cargo Box #TH05603 which includes everything you need to get your Sears X-Cargo back on the road. No drilling would be…

view full answer...

Answer 4

For your Sears SV-20 Cargo Carrier, you can use the Replacement Lid Lifter Hinge for Thule Cargo Boxes #TH14936.

view full answer...

Answer 5

To replace the mounting hardware on your Sears X-Cargo Sport 20 cargo carrier you can use the Replacement Hardware Kit #TH05603 to re-mount your cargo carrier on most factory and aftermarket roof rack crossbars. To replace the lock, you'll want…

view full answer...

Answer 6

I spoke with my contact at Thule and was informed that for the Sears branded Sport 20-SV cargo box you would need to use hinge #TH14936. My contact also stated that both hinges should be changed at the same time for best performance. I have linked a…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Lid Parts for Sears X-Cargo Sport-20 Rooftop Cargo Box

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching