How Much Bed Space Do Access # A60085 Truck Bed Storage Pockets Take

Question

Question:

If installed in a 2015 dodge ram 1500 will there still be clearance to slide in 4x8 sheets of plywood between the wheel wells

asked by: Steve C

0

Expert Reply:

The Access HD Aluminum Treadplate Truck Bed Storage Pockets are constructed of aluminum treadplate that's right about 1/8 inch thick. Using one pocket on each side would take up about 1/4 of an inch or so of the distance between the wheel wells.

Measure the current distance between your wheel wells, and subtract about 1/4 of an inch, this should give you the available space between the wells if the pockets were used.

expert reply by: Mike L

0

Answer 1

Hey Ron, The license plate light is typically spliced into the running light circuit so that it has power anytime the headlights are on. Since the Curt Custom Tail Light Wiring Kit for Towed Vehicles #C96JR would be just transferring your…

view full answer...

Answer 2

I believe what you are looking for is the Kwikee SuperSlide II Tray Assembly Kit for RV Cargo Compartment #LC370762. This is 90" deep so that matches but the smallest trim piece we carry width-wise is part #LC370676 which is 24" so this is…

view full answer...

Answer 3

Hello Mike, thanks for reaching out. Our best over-the-bed crossbar option for the 2025 GMC Sierra EV is the Yakima BedRock HD Truck Bed Rack #Y01160-59. The EV model is quite new, so we have not had a chance to test fit this, and there is no fitment…

view full answer...

Answer 4

I recommend using the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole Connector - 6' Long #HM41158. It mounts in the truck bed sidewall, tailgate post or the wheel well. It will plug into your factory wiring.

view full answer...

Answer 5

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 6

According to the installation instructions, the torque specification for the 2-5/16" ball that comes with the Blue Ox 2-Point Weight Distribution w/ Sway Control - 6-Hole Shank - 10K GTW, 1.2K TW item #BLU75FR is 260 ft lbs. The socket you will…

view full answer...

Answer 7

I looked online and found the owner's manual which said your 4WD 2007 GMC Envoy with a 6 cylinder had a towing capacity between 5,200 lbs and 6,200 lbs depending on your axle ratio. A 3.42 axle ratio gives you 5,200 lbs of capacity, a 3.73 axle…

view full answer...

Answer 8

I called TruXedo and they were able to look up your serial number to confirm you have cover 297644 which is indeed a Ford cover. My contact there believes the part you are referring to is either a latch kit like #TX1117755 or the passenger rear…

view full answer...

Answer 9

I went out to the warehouse and pulled the Replacement Hitch Ball for B&W Turnoverball Underbed Gooseneck Hitches, part #BWGNXA2000, and took some measurements for you. The square part of the hitch ball is 4" long and 2-1/2" wide. The…

view full answer...

Answer 10

Hey Alex, would you consider an air bag kit? We have the Air Lift LoadLifter 5000 part #AL57388 that is a confirmed fit for the AT4 models of your 2025 GMC Sierra 1500 if so. Let me know if that would work or not.

view full answer...

Answer 11

The correct fitting BullRing tie-downs for your 2021 GMC Sierra 3500 are new, which is why they've been hard to find until now. You'll need the BullRing Stake Pocket D-Rings #BU94VR. These tie-downs are only compatible with the stake pockets…

view full answer...

How Much Bed Space Do Access # A60085 Truck Bed Storage Pockets Take

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching