Install Instructions and Owners Manual for the Roadmaster Tow Dolly part # RM-2000-1

Question

Question:

Hello, how do I aquire an owners and service manual, for the tow dolly, above? Thank you

asked by: Jim A

1

Helpful Expert Reply:

I attached the install instructions and owners manual for the Roadmaster Tow Dolly part # RM-2050-1 that you referenced. They are linked on this page under the words, "Featured Help Information."

expert reply by: Jameson C

1

Answer 1

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 2

Because the front axle of the towed vehicle sits over the axle of the tow dolly, very little weight is transferred to the tongue of the tow dolly. I spoke with my contact at Roadmaster and he said the Roadmaster Tow Dolly, #RM-2050-1, was engineered…

view full answer...

Answer 3

Yes, the Roadmaster Tow Dolly part #RM-2050-1 is made right here in the U.S.A. This tow dolly is actually one of the most well equipped tow dolly's on the market with self-steering wheels for increased maneuverability, electric brakes for…

view full answer...

Answer 4

According to Honda, the 2010 Honda Accord cannot be flat towed with all 4 wheels on the ground. Your best option to tow your vehicle will be to use a tow dolly like the Roadmaster Tow Dolly w/ Electric Brakes, #RM-2050-1. The tow dolly will allow…

view full answer...

Answer 5

The best tow dolly we offer is the Roadmaster Tow Dolly with Electric Brakes part #RM-2050-1. Dolly includes all lightging as well for DOT compliance. The only thing one would need to use this dolly is a trailer connector like part #PK11604 for a…

view full answer...

Answer 6

Hey Mark, I took the Replacement Passenger's-Side Stop/Turn/Tail Light for Roadmaster Tow Dolly #RM-300220-30 apart and found that it uses a 1157 bulb type. If you want to stick with incandescent you can use part #A1157B or you can upgrade to…

view full answer...

Answer 7

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Nelson, so you would need two separate systems since a supplemental braking system can only be used with a towed vehicle and a trailer brake controller can only control trailer brakes. Main difference is a supplemental braking system is designed…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Install Instructions and Owners Manual for the Roadmaster Tow Dolly part # RM-2000-1

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching