Replacement Shank Bolts for a Reese Strait-Line Weight Distribution System

Question

Question:

where can i find the shank bolts

asked by: Timmey

0

Expert Reply:

For Reese weight distribution system # RP66082 you can use replacement bolt kit # 58133. It comes with the bolts, square adjustment washers, lock washers, and nuts.

expert reply by: Michael H

0

Answer 1

A parking brake system, also known as an e-brake, can only be used if the brake assemblies are already equipped with a parking brake. Dexter does offer electric brake assemblies with a parking brake, but their standard electric brakes assemblies…

view full answer...

Answer 2

That's a good question Barry, and electric brakes like #23-468-469 do use 16 gauge wiring for the pigtails. But we do recommend using 10 gauge to connect to the brakes simply because of how far the wiring generally has to be run on trailers. I…

view full answer...

Answer 3

The grease zerk fitting on your MORryde 3000 is M6 x 1.0 according to my contact at MORryde. To replace this you need the following part: Replacement Brass Grease Zerk for Weld-On Hinges - #MA35ZR This was designed for a weld-on hinge but since it…

view full answer...

Answer 4

Other than the 2022 Toyota Tundra and the 2019+ GMC Sierra 1500 Denali, I'm not aware of any other currently available composite bed trucks. None of our vendors yet offer a 5th wheel bracket/rail option for the 2022 Tundra, but Curt offers the…

view full answer...

Answer 5

The Replacement Bolts and Washers for Reese High Performance Trunnion Weight Distribution (WD) Head #58133 that you referenced is compatible with the Head for Reese Weight Distribution System #RP58167 that is used for your discontinued 66152 WD hitch…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

The Tru Ryde grease seals you mentioned, part #RG06-70 are indeed a replacement for the 10-036-00 Dexter seals. They would work great for your application.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Replacement Shank Bolts for a Reese Strait-Line Weight Distribution System

Continue Researching