Trailer Brake Controller Wiring Connector Location on 2015 Toyota Tundra

Question

Question:

I bought a tekonsha brake control and wire harness for my 2015 tundra but cant find where it plugs In

asked by: Tim

0

Expert Reply:

The brake controller connector is clipped to the back side of a panel located just to the right of the ignition key. You'll need to lower the panel and unclip the connector from the rear of the panel, then feed it down behind the panel so it exits out the bottom of the dash. I've edited a photo showing the location of the connector, and I've linked you to the install instructions for the # 3031-P.

I've also linked you to our Brake Controller FAQ article, which contains more information about brake controllers.

expert reply by: Mike L

0

click to enlarge

Answer 1

The brake controller port for the 2015 Toyota Tundra is located behind the section of the dashboard with the tow/haul button. To reach the connector you will need to locate the notch in the access panel in the center of the dash near the driver's…

view full answer...

Answer 2

The connector for the #3031-P Brake Controller wiring harness is located behind a panel just to the right of the steering column as shown in the linked install instructions, the video and the provided photo.

view full answer...

Answer 3

Great news! I can help you find the brake controller harness on your truck. Since you have a factory tow package on your 2016 Toyota Tacoma you will have a plug for a brake controller in your dash. According to the instructions on the #3031-P harness…

view full answer...

Answer 4

The Tekonsha Primus IQ #TK90160 will work great on your 2015 Tundra. If you have the factory 7-way trailer connector you can use the plug-in adapter #3031-P for the brake controller. If you do not have a 7-way connector you will need to hardwire the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Trailer Brake Controller Wiring Connector Location on 2015 Toyota Tundra

Featured Help Information

Miscellaneous Media

Continue Researching