Replacement Install Hardware for DeeZee Tailgate Assist # DZ43301

Question

Question:

I need a new nut . Will you sell me the product . I have a 1500 Ram Truck 2011 .I striped the nut device piece . All I need is the expansation device . This for your a tailgate assist product.Please let me know ASAP Thank you

asked by: Kenneth K

1

Helpful Expert Reply:

We offer a replacement hardware kit, part # BKT43301 that includes all the hardware, minus the gas shock. The nutsert that installs into the side of the tailgate that provides an attachment point for the shock isn't sold as a separate item.

expert reply by: Mike L

1

click to enlarge

Answer 1

DeeZee Tailgate Assist Custom Tailgate-Lowering System #DZ43301 does have what they call a nut zerk fitting like what you show in your picture. If you just need to replace that part use #BKT43301. You have to be very careful not to over tighten this…

view full answer...

Answer 2

For the DeeZee tailgate assist we have the replacement hardware kit part #BKT43301 that comes with the new bolt you are looking for plus a few other things that you could keep as replacement parts.

view full answer...

Answer 3

The MagnaFlow Cat-Back Exhaust System #MF15333 is confirmed to fit a 2018 Ram 2500 Crew Cab with an 8 Foot Bed or Mega Cab with a 6-1/2 Foot Bed and a 6.4L V8 HEMI. The installation details have been linked for you to reference.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Install Hardware for DeeZee Tailgate Assist # DZ43301

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching