Replacement Vent Cover Recommendation for a Rockwood Signature Travel Trailer

Question

Question:

I have a 2009 Rockwood Signature Ultra Lite travel trailer. model 8317 SS When the snow melted I went to get it out of storage and the vent covers on both bedrooms were gone disintegrated. Can you tell me which cover are a direct replacement?

asked by: Phil S

0

Expert Reply:

Most likely we have what you are looking for but you will need to first determine what vent you have on your trailer.

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14".

To pick the correct cover, you will also need to know the type of hinge you need.

There is a 3 point hinge, such as the one on the Camco # CAM40153; a 4 point hinge as seen on the Camco # CAM40154; or a rolled metal continuous hinge like on the Ventline # BVD0449-A03; and universal hinge as shown on the MaxxAir # MA00-335001.

Basically the easiest way to select the correct replacement cover is to remove the existing cover and match the hinge and lift bracket to the photos on our site along with the dimensions. A link to all of the replacement vent covers is provided to match up with your cover.

If it is not clear which hinge style that you have, the MaxxAir above is a Universal Replacement Lid.

In the event that you don't find a lid you like, I also included a link to our main page for our complete 14 x 14-inch vent assemblies. These are offered in manual or powered lift and with or without fans. If you install a complete new vent you'll need an installation kit, either # 344270KITW for a metal or coated metal roof or kit # CAM25013 for a rubberized roof..

expert reply by: Jameson C

0

Christine

4/4/2020

Question this bv0554-01 does it come in a smoke?

Chris R.

4/6/2020

Yep - for the Smoke version you'll just use part # BV0554-03.

Answer 1

We do have some products that will work to join to sewer hoses together but not one that uses lugs on both sides. What we do have are the threaded adapter #F02-3102 and a non-threaded, similar version #CAM39203. I have linked videos on both parts for…

view full answer...

Answer 2

Yes, the temperatures you mentioned are normal. If you were getting over 200 degrees that would be a bad sign. But typically if all of the hubs are the same temperature you're good and it's only really an issue if one of the hubs is hotter…

view full answer...

Answer 3

A bad ground can cause just one brake assembly to get hotter only as a result of the assembly with the bad ground not engaging, which in turn causes the assembly on the other side to do all the work (thus get hotter). It appears though that both…

view full answer...

Answer 4

I have a few options for you to help with identifying the bearings and seals on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Vent Cover Recommendation for a Rockwood Signature Travel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching