Rear Suspension Enhancement Recommendation for a 2014 Ram 2500 with Coil Springs

Question

Question:

I have a 2014 ram 2500 and it has coil springs and not leaf looking for something for my rear suspension like air bags or what ever you think I should install to help I tow a 38 foot fifth wheel around 15000 lbs need a little help with the in the back please let me know part number to take a look at what I need Thank you

asked by: Terrell E

0

Expert Reply:

I would recommend the Timbren Rear Suspension System part # TDR2500D for your 2014 Ram 2500 with coil springs.

This system has been confirmed to fit your vehicle that has coil springs and will provide you with additional suspension support when the vehicle is loaded. Also, it won't affect your ride quality when unloaded unless you were to hit a large bump. I attached a picture a customer of ours sent us that shows it installed in a truck with coil springs just like yours.

Timbrens are nice because they don't require maintaining air pressure like the air bag kits do.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It is typical to have approximately 1/2 inch of space between the bottom of the bumper and the axle. Removing the spacer will help to improve the ride quality. With the spacer gone, the distance increases to 1-1/2 inches, and will improve ride…

view full answer...

Answer 2

Yes, the Timbren suspension enhancement system (SES) jounce-style springs will help to level your 2015 Ram 2500 when you are under a load. The correct part you want to use is #TDR2500D as the other part for the rear suspension, part #TDRTT3500E, is…

view full answer...

Answer 3

If you're saying the space where the Timbren would install is 7" you wouldn't need a spacer. About an inch gap is what is recommended, and the Timbren #TDR2500D for your truck measures 5-3/4" in overall height. A 1" spacer is…

view full answer...

Answer 4

Due to the design of the Timbren Rear Suspension Enhancement System #TTORTAC4A on your 2002 Toyota Tacoma the screw that would normally sit in that position is welded on as you do not have access to the head of the screw when it is installed on your…

view full answer...

Answer 5

If you're wanting to install the Timbren #TFR350SDJ on your 2022 Ford F-350 then you'll want to measure the distance from where your factory bump stops are installed down to the point of contact on the axle. The Timbren #TFR350SDJ are…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Rear Suspension Enhancement Recommendation for a 2014 Ram 2500 with Coil Springs

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching