Availability of a Replacement Castle Nut for a Harbor Freight Trailer

Question

Question:

Hi, I need a castle nut for my Harbor Freight trailer to hold on the hub. I think its a 25mm. Do you have it.

asked by: Gary

0

Expert Reply:

25 mm is very close to 1 inch, so there is a good chance the castle nut part # 165686 would fit as it is 1 inch. That said we've had customers tell us it's actually 22 mm which we don't carry.

expert reply by: Jameson C

0

Answer 1

I looked up the dimensions of your High Pointe EC942K9E and it's 15 inches deep, 15.7 inches tall, and 29.9 inches wide so the Furrion Over the Range RV Convection Microwave #FMCM15SS that you referenced would easily fit in place of it and would…

view full answer...

Answer 2

Since all you are needing to replace is the converter for your Progressive Dynamics PD4575K18L, you will need the Replacement Lithium Converter for Progressive Dynamics 4500 Series item #PD4575LICSV. This converter will replace your 75 amp PD457518L…

view full answer...

Answer 3

The diagram also shown here is showing the outside and inside of just the trailer side connector of a 7-Way round pin. It is not showing the vehicle side which would be a mirror opposite. I have also included a vehicle side diagram that shows the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Availability of a Replacement Castle Nut for a Harbor Freight Trailer

Product Page this Question was Asked From

Continue Researching