Welding Latch Pin Installation for Securing Trailer Ramp

Question

Question:

I watched the video on the part and I still dont understand how it is welded in order for it to work. I want to use two of the latch pins to secure the tailgate on my 5 x 10 utility trailer. Any possibility of a picture of this application?

asked by: Ric H

1

Helpful Expert Reply:

I attached a picture that shows how the # SL58W will install on a trailer with a ramp. I used arrows to point out the latches and the holes that it will fit into when folded up and latched.

I also attached a picture that shows where you would weld the # SL58W to your trailer and where you would drill the hole in the ramp so that the pin would insert into it and secure it.

expert reply by: Jameson C

1

click to enlarge

Answer 1

I do have some parts for you but we aren't custom trailer builders and adding electric to a trailer is not a simple task. What I can tell you is that most interior lights are 12 volt so if you want outlets, lights, and shore power you'd need…

view full answer...

Answer 2

The blue and green lights on the Redarc Tow-Pro Elite #RED44FR and Liberty #RED24FR Brake Controllers flash while the brakes are being depressed until the controller confidently learns the exact orientation. Do understand if there is a bad power…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

Hey Dale, thanks for reaching out. For your 2010 Toyota Tundra with the factory tow package, a proportional controller is definitely the way to go for smooth braking on a 2-axle trailer, and a really clean option is the Redarc Tow-Pro Liberty…

view full answer...

Welding Latch Pin Installation for Securing Trailer Ramp

Product Page this Question was Asked From

Continue Researching