Replacement Door Handle and Latch for an Enclosed Cargo Trailer

Question

Question:

I need a door hook and latch nine to twelve inches long. I have a cargo trailer with two back doors the latch I have is about ten inches long plastic of some kind with a 3/4 in ball at each end. having trouble finding one this long. thanks

asked by: Mike B

0

Expert Reply:

The handle and latch we currently offer is the Universal cam-door lock # 383200 for enclosed trailers. The handles measures 13-3/4 inches long so it may be a little long for your trailer.

If you don't have a pipe, you will need a 3/4-inch inner diameter one.

If you need to hold your trailer doors open, you can use the Redline enclosed trailer part # PLR64-66. It will create a gap between the door and trailer of 2-5/8 inches.

I included a video review for you as well.

expert reply by: Chris B

0

Answer 1

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 2

Hey Paul, the Advent Air RV AC unit part #ADV99QR that you referenced comes with a wall mounted thermostat that the remote part #ADV67QR communicates with. So there wouldn't be a way to just use a wireless remote with the Advent AC unit without…

view full answer...

Answer 3

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 4

For the barn door on your dump trailer, I recommend looking at the Cam-Action Lockable Door Latch Kit #383200. This is a nice steel cam-action door latch with a 1 inch wide hasp that can be installed flush on doors with a 3/4 inch offset. It features…

view full answer...

Answer 5

Hi Jean, thanks for reaching out. The locking cylinder part #A522VP is not available in a keyed alike set, so if you're looking to have all of your service body compartments and maintainer doors operate with a single key, that isn't an option…

view full answer...

Answer 6

Hey Matt we still have that screw kit. It is the Replacement Jack Screw and Nut Kit for Bulldog Sidewind Trailer Jacks item #BD500217. This is designed to fit Bulldog series 182 jacks from 2003 to present with a 12,000 lb capacity. I have linked a…

view full answer...

Answer 7

We carry all sorts of RV door parts including hinges and latches that you can see on the linked pages. I included links to hinges, latches and weather-stripping like #WS1434 and vinyl trim like #CAM25103. Since trailer makers do not keep track of…

view full answer...

Answer 8

Hey Mike, yes the replacement cap part #T097-022-00 that you referenced is the correct replacement cap for a Dexter Model A-60/A-75 brake actuator like it sounds like you have.

view full answer...

Answer 9

According to the manufacturer the pipe is the 1 inch schedule 40 pipe which means the inner diameter is 1 inch and the outer diameter is 1-5/16" so the attached video and the video are correct. I have also attached a photo from the manufacturer…

view full answer...

Answer 10

Hey Jesse, cool name! That's definitely a custom project, and there isn't a single off-the-shelf kit that'll give you everything you need. For a lift-up wall that's around 10' x 6', you're looking at building the door and…

view full answer...

Replacement Door Handle and Latch for an Enclosed Cargo Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching