Hitch Step Recommendation for a 1-1/4 inch Hitch

Question

Question:

Can any of your trailer hitch steps, like the mega step be fitted for the smaller 1 inch hitch hole? I love the one that is for pets and that is what I am looking for but I will not pay that kind of money for a pet step. Can you help for under $75 bucks?

asked by: Lisa K

0

Expert Reply:

The Pilot Hitch Step part # CR-605 has been confirmed to fit 1-1/4 inch hitches and isn't quite as pricey as the # HE3052 that you also referenced.

The # CARR190011 is only designed to fit 2 inch hitches.

expert reply by: Jameson C

0

Answer 1

I went out and measured the PortablePET Twistep, part #HE3052. I've included a diagram that details the measurements from the center of the hitch pin hole to the back plate of the swivel, which will always be the closest part. The closer of the…

view full answer...

Answer 2

The Heininger PortablePET Twistep Hitch Mounted Step #HE3052 can be set to several different heights. This can be seen in the linked video at the :43-second mark. 4 bolts are used to set the platform height. At the lowest height setting the TOP of…

view full answer...

Answer 3

Hey George, yes we do have a rain cover for the Watchdog Power Center part #HU74ZR with the part #HU88FR.Did you have the previous generation Watchdog?

view full answer...

Answer 4

You can use a threaded hitch lock with the PortablePET Twistep Hitch Mounted Step #HE3052 on your Forester's 1-1/4" hitch, though not one with just a 3/8" non-threaded portion as it isn't long enough; that said, we do have a hitch…

view full answer...

Answer 5

The Hitch Stair with 2 Steps #RHS2 that you referenced weighs 19 lbs and has a weight capacity of 250 lbs. I attached a review video for this for you to check out as well.

view full answer...

Answer 6

I would be happy to help. It sounds like you are looking for the Demco 2-Tang Clevis #DM12676-95 which will fit perfectly in the Curt Channel Style Adjustable Ball Mount #C45900 you have. The clevis bolt is not included but a 1" diameter bolt…

view full answer...

Answer 7

Brian, you’ll each want the version that matches your RV’s service. The #HU84ZR is built for 30A rigs like your friend’s Cougar, while the #HU74ZR is made for 50A rigs like your Cedar Creek. They both do the same job - voltage boosting, surge…

view full answer...

Answer 8

The correct replacement anti rattle hitch pin for your Yakima HoldUp Bike Rack #Y02445 is the Replacement Mounting Hardware for Yakima HoldUp #Y8880129. Unfortunately this, like most other bike rack anti rattle hitch pins is a proprietary pin and…

view full answer...

Answer 9

It sounds like maybe your anti-rattle wedge was stripped or damaged on your rack, especially if your able to remove it from the rack completely. The correct replacement part for this is the #8880508. This is a replacement SpeedKnob and wedge for the…

view full answer...

Answer 10

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

Answer 11

Hi Nick; the brackets and index bars for the etrailer RapidRamps #e47XV are not available separately. At this time, the only way we offer them is with the ramps. What are you planning to use the ramps for?

view full answer...

Hitch Step Recommendation for a 1-1/4 inch Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching