Trailer Tie Down Anchors

Hello Matt, Thanks for writing in. Yes, you can mount the Caliber D-Ring Anchor Kit #CA89VT vertically on the side of your skirted flatbed. These are a universal mount, so mounting them vertically does not change the 5,000 lb capacity. You will just…

Hi Wayne, I went out to the warehouse and measured the Caliber D-Ring Anchor Kit part #CA89VT for you. The plate dimensions are 4" long by 3 3/4" wide and the inner diameter of the ring is 1 1/4" and outer diameter is 2 1/4". What…

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

Hello Ben, Thanks for writing in! Yes! The WeatherTech Front Auto Floor Mats #WT54TZ you were looking at are made specifically for the factory vinyl floor in your 2026 Ram 2500. For the rear, WeatherTech does not have a matching custom-fit rear mat…

Hey Victor. Unfortunately, the Pacbrake Airbags #PB36SV you mentioned are not going to fit your trucks specific configuration (Trail Boss & OEM puck system). The fitment on these is confusing as there's a lot of different orientations of…

Hey George! Assuming you're looking for a complete kit, the Erickson ATV E Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM98CV you were looking at covers just about everything. This is compatible with 10" - 30" diameter tires,…

Hey Dave, thanks for reaching out! The Erickson Round D-Ring Tie-Down Anchor #EM59110 has a capacity of 1,200 lbs and is not going to be strong enough to cinch down your Polaris RZR securely. You need the CargoSmart Anti-Rattle D-Ring Tie-Down Anchor…

We do not sell a complete kit but we do sell a backing plate that is compatible with the Square D-Ring Tie-Down Anchor item #ABS69FR. It is the Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor item #BP05.

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

Welcome back Jordan! I have an alternative for you but we do not have any Ram 7k jacks that can be bolted on. Just welded like item #TJD-7000S and pipe mount like item #TJDP-7000S-B options. For a 7,000 lbs capacity square jack that can be bolted on,…

Hey Steve, the Rubber Door/Hatch Seal for RV and Trailers #SR98ZR comes with the adhesive needed to install it so really you just need to clean the surface you plan to install it on and it would be ready to be put on!

I would measure the distance between the center of one bolt hole to the center of the bolt hole adjacent to it, and not the diameter. If the distance is: 2-5/8" - the bolt pattern is 5 on 4-1/2 2-3/4" - the bolt pattern is 5 on 4-3/4…

Hello Matt, Thanks for writing in. Yes, you can mount the Caliber D-Ring Anchor Kit #CA89VT vertically on the side of your skirted flatbed. These are a universal mount, so mounting them vertically does not change the 5,000 lb capacity. You will just…

Hi Wayne, I went out to the warehouse and measured the Caliber D-Ring Anchor Kit part #CA89VT for you. The plate dimensions are 4" long by 3 3/4" wide and the inner diameter of the ring is 1 1/4" and outer diameter is 2 1/4". What…

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

Hello Ben, Thanks for writing in! Yes! The WeatherTech Front Auto Floor Mats #WT54TZ you were looking at are made specifically for the factory vinyl floor in your 2026 Ram 2500. For the rear, WeatherTech does not have a matching custom-fit rear mat…

Hey Victor. Unfortunately, the Pacbrake Airbags #PB36SV you mentioned are not going to fit your trucks specific configuration (Trail Boss & OEM puck system). The fitment on these is confusing as there's a lot of different orientations of…

Hey George! Assuming you're looking for a complete kit, the Erickson ATV E Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks #EM98CV you were looking at covers just about everything. This is compatible with 10" - 30" diameter tires,…

Hey Dave, thanks for reaching out! The Erickson Round D-Ring Tie-Down Anchor #EM59110 has a capacity of 1,200 lbs and is not going to be strong enough to cinch down your Polaris RZR securely. You need the CargoSmart Anti-Rattle D-Ring Tie-Down Anchor…

We do not sell a complete kit but we do sell a backing plate that is compatible with the Square D-Ring Tie-Down Anchor item #ABS69FR. It is the Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor item #BP05.

A keen observation indeed, Brett. The mounting hole spacing on the Square D-Ring Tie-Down Anchor #ABS69FR is 3" horizontally and 3-1/4" vertically. I edited a picture for you to help illustrate.

Welcome back Jordan! I have an alternative for you but we do not have any Ram 7k jacks that can be bolted on. Just welded like item #TJD-7000S and pipe mount like item #TJDP-7000S-B options. For a 7,000 lbs capacity square jack that can be bolted on,…

Hey Steve, the Rubber Door/Hatch Seal for RV and Trailers #SR98ZR comes with the adhesive needed to install it so really you just need to clean the surface you plan to install it on and it would be ready to be put on!

I would measure the distance between the center of one bolt hole to the center of the bolt hole adjacent to it, and not the diameter. If the distance is: 2-5/8" - the bolt pattern is 5 on 4-1/2 2-3/4" - the bolt pattern is 5 on 4-3/4…